Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Antioch Owner’s Guide
Schluter bathroom remodeling in Antioch typically runs $9,000 to $28,000 installed, depending on shower size, tile choice, and whether we’re rebuilding a failed waterproofing system or starting fresh. We’re an independent contractor, not affiliated with Schluter, and we install and repair Schluter-bonded showers, floors, and wet areas across Antioch.
Most Antioch owners don’t call us because they know the brand name. They call because something went wrong six months after a shower was “finished.” Grout at the curb keeps turning dark. A tile near the drain sounds hollow when you tap it. The baseboard on the other side of the shower wall feels soft, and that’s usually the moment the phone comes out.
Behind almost every one of those calls is the same story: the tile was set correctly, but the Schluter waterproofing layer underneath was installed wrong, or the wrong Schluter product was used for the assembly in the first place. Tile is the visible part. The membrane and the drain are the parts that decide whether a $12,000 shower survives five years or fifty.
Which Schluter Models This Applies To
Schluter doesn’t sell one shower system; it sells a family of them, and identifying which one is already behind your tile matters before anyone quotes a repair.
- KERDI and KERDI-BAND: The bonded sheet waterproofing most Antioch showers are built on. If your waterproofing failed, the seams and corners are almost always where it started. KERDI comes in 5-meter and 30-meter rolls at widths from 3’3″ to 5′ wide, and the band is sold in 4″ and 5″ widths. Getting the band width wrong at a curb or bench radius is a common failure point we find.
- KERDI-BOARD: A waterproof foam backer board. Comes in thicknesses from 1/8″ up to 2″ and panels up to 4′ by 8′. If your shower walls are set on KERDI-BOARD, you can’t substitute cement board during a repair without rebuilding the whole wall.
- KERDI-LINE and KERDI-DRAIN: The linear and center-point drains. KERDI-LINE channels are available in nominal lengths from roughly 20″ to 72″ with different grate styles. Matching a discontinued grate finish is the single most common parts headache we run into in Antioch bathrooms.
- DITRA and DITRA-HEAT: The uncoupling membrane under floor tile, plain or with heating cable. If your bathroom floor tile cracked in a line, DITRA was either skipped or installed without the right thin-set.
- SCHIENE and JOLLY: The edge profiles. These aren’t structural, but if a piece is loose or the anodized finish is chalky, matching the profile series and finish to the rest of the room is the whole job.
The OEM-versus-aftermarket decision is real here. Schluter-brand membrane and drain assemblies are spec’d as a system, and mixing a generic membrane with a Schluter drain flange voids the assembly logic even if each piece looks fine alone. Cheaper unbranded fleece-faced membranes exist. We don’t install them, because in a wet-walled Antioch shower, the seam tape is the part that fails first and it’s the part nobody sees.
To identify the right part, pull the drain grate if you can access it (it lifts straight up on most KERDI-DRAIN models) and match the opening dimensions and grate finish. For membrane, look at the printed line on any exposed edge or photograph the curb and niche corners before demolition starts.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
Every symptom below points to a specific cause. If you recognize two or more, it’s worth a walkthrough before the problem spreads into the framing.
- Dark, re-wetting grout at the curb or shower floor. Water is sitting under the tile instead of draining through the KERDI-DRAIN weepholes. That usually means the mud bed was packed over the drain flange, or the membrane was laid flat instead of sloped.
- Hollow-sounding tile near the drain. The thin-set bond has let go, often because the membrane wasn’t embedded into fresh thin-set or the wrong thin-set was used. A hollow tile is a loose tile waiting to crack.
- Soft drywall or a musty smell on the far side of the shower wall. The KERDI seam tape at a corner or the shower valve penetration has failed. This is the most expensive symptom because it’s the one that reaches framing and subfloor.
- Cracked floor tile along a straight line. Either DITRA was omitted over a wood subfloor, or the tile was set directly on plywood. Floor movement telegraphs straight through tile without an uncoupling layer.
- Loose or corroded edge profile. A SCHIENE or JOLLY piece that’s popped off, or a drain grate with white crust and pitting. In Antioch’s hard water, mineral buildup on a grate can look like corrosion and hide a clogged weephole underneath.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Replacement and rebuild ranges for Antioch, installed and with labor included:
| Scope | Installed Price Range |
|---|---|
| Schluter bathroom remodel, full scope (membrane, tile, drain, fixtures) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower with Schluter system | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement and waterproofing rebuild | $3,000 – $8,500 |
| Vanity installation (Schluter substrate, tile surround) | $800 – $3,000 |
The range is driven by three things: shower footprint (a 36″ shower and a 60″ shower use very different amounts of membrane and tile), whether the walls need KERDI-BOARD replacement rather than a patch, and tile selection. Schluter drain and profile finishes are a line item, not an upcharge hidden in tile price. We quote membrane, drain, thin-set, and labor separately so you can see where the money goes.
The number you see is the number you pay. Every Groundwork job in Antioch is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. Financing at 0% for 18 months is available, and projects over $10,000 get $1,000 off.
DIY or Call Us?
What you can safely check on your own: lift the drain grate and look for mineral buildup blocking the weepholes; photograph the curb and niche seams so you understand where the waterproofing boundary is; and poke the drywall on the far side of the shower wall for softness. That’s the extent of safe owner inspection on a Schluter assembly.
What goes wrong when it’s done DIY: waterproofing is the part where a wrong seam is invisible until water has already reached the subfloor. A homeowner who re-tapes a KERDI corner without embedding it in Schluter’s own thin-set, or who fills the mud bed over the drain flange, has built a shower that will leak in six to twelve months. The tile will look perfect the whole time. That’s the trap. Demolition, drain flange replacement, and repair of a failed membrane are not weekend jobs, and a failed assembly that gets re-tiled without correcting the waterproofing layer is money thrown away.
The safety issue with this work is less about injury and more about hidden damage. If the framing is already wet and soft behind a failed shower, we need to see it before anyone seals it back in. Call (888) 419-3650 for a free estimate and we’ll walk the shower with you.
FAQs
A correctly installed Schluter shower assembly lasts 25 to 30 years or more, and the two biggest variables are seam execution and slope to the drain. A shower built with proper thin-set embedment, banded seams, and a sloped mud bed to the KERDI-DRAIN weepholes is a long-lived system. A shower where the membrane was laid flat has a much shorter life, often closer to 5 to 10 years before the grout re-wetting and drywall softness show up. Call (888) 419-3650 for a free estimate and we’ll tell you which you have.
Sometimes yes, and it depends entirely on where the failure is. A single lifted edge profile or one hollow tile near the drain can often be repaired without a full tear-out. A failed membrane at a curb corner or a shower valve penetration almost always means the assembly needs demolition from the tile to the backer to reach the waterproofing layer and correct it. There’s no honest way to fix a compromised membrane from the tile side. Call (888) 419-3650 and we’ll scope it free.
A full Schluter bathroom remodel in Antioch typically takes 2 to 4 weeks from demolition to final walkthrough, and a straight shower replacement without moving plumbing usually runs 1 to 2 weeks. The waterproofing stage adds at least one drying day between membrane and tile that a cheap bid will skip. Call (888) 419-3650 for a free estimate and a written timeline for your specific bathroom.
We source Schluter membrane, drains, and profiles through authorized supply channels and confirm the exact part number against your existing assembly before ordering. Matching a discontinued drain grate or an older SCHIENE finish is the trickiest request we get in Antioch, and it’s usually solvable by measuring the grate opening and photographing the profile, not by guessing the model. If a finish is genuinely discontinued, we tell you upfront and give you the closest current option. We don’t stock Schluter parts on a vehicle; each project is ordered to spec. Call (888) 419-3650 for a free estimate.
Written by the team at Groundwork Construction Co. of Antioch, serving Antioch and nearby areas.