Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Windows & Doors: The Antioch Owner’s Guide
We install Tamko-compatible windows and doors for Antioch homeowners, and typical installed pricing runs $4,500 – $15,000 for window replacement on up to eight to ten openings, with impact-rated units at $8,000 – $25,000. Foreign-brand parts on an older Tamko frame usually land at the lower end because you’re swapping hardware, not the whole unit. Tamko is actually better known in this market for roofing and waterproofing products, so when an Antioch homeowner calls us about “a Tamko window part,” it’s almost always one of three things: a sagging or cracked sill from dry-rot, a failed weatherstrip or sweep that’s letting in Contra Costa wind, or a hinge or latch that’s stripped out after 15-plus years of East County summer heat cycling. We see it most in the older housing stock around the Riverview and downtown Antioch corridor.
Which Tamko Models This Applies To
Tamko’s window and door hardware footprint is smaller than its roofing line, so the first honest step is confirming what you actually have. Look for a label or etched code on the glass edge or the top of the sash frame; if it’s gone, measure the visible glass and the rough opening to the nearest 1/16 inch. Many Antioch homes we service are running Tamko rain-carrying and flashing products installed by a prior builder, with actual window units from another manufacturer set into a Tamko-weatherproofed opening. That distinction matters: a Tamko sill pan or flashing repair is a $400 – $1,800 job, while a full window replacement is a $4,500 – $15,000 project. We’ll tell you which one you’re looking at before we quote. When the Tamko part is discontinued, we source a spec-matched OEM equivalent or a same-spec aftermarket piece, and we tell you which one we’re using and why. We’re an independent service provider, not affiliated with Tamko.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Windows & Doors Is Failing
- Water staining or soft wood at the sill. In Antioch, the Delta moisture pattern punishes south-facing sills hardest; a soft sill usually means the flashing beneath it has failed, not just the paint.
- Drafts around the sash or door edge. Worn weatherstrip or a cracked sweep lets our afternoon west winds leak in. If you can feel air at a closed window, the seal is gone.
- Sticking, hard-to-close operation. Heat cycling on an East County summer warps the frame slightly and the hardware stops aligning. This one gets worse if you force it.
- Condensation between panes. A failed insulated glass seal is a glass-unit replacement, not a hardware swap. Expect to pay more than a $200 latch job.
- Visible cracks or separation at the frame-to-wall joint. Often a flashing or caulk-line failure that lets water behind the wall. Fix the flashing before it reaches the interior.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Antioch, installed window replacement runs $4,500 – $15,000; impact-rated units run $8,000 – $25,000 when you’re upgrading to that spec. What moves the number: how many openings, single versus double-hung, whether the rough opening is already correct, and whether we’re pulling a permit. Repair-only jobs on Tamko-compatible hardware and flashing sit at $400 – $1,800. Every quote is line-itemed so you see parts, labor, and disposal separately; the number you see is the number you pay. The work carries our 730-Day Done Right Promise, and we pull the permits the job requires.
DIY or Call Us?
You can safely check for drafts with a smoke pencil or a tissue, measure the glass and rough opening, and photograph any label or etched code for us. You can also re-caulk a failed exterior joint if you’re comfortable on a step ladder. What we’d rather you not do: pull a window or door frame out of a second-story opening, cut into wall sheathing to trace a leak, or try to free a seized hinge by force, which can crack the sash. Those are the calls that turn a $400 repair into a $4,500 – $15,000 replacement. Call (888) 419-3650 and we’ll tell you over the phone whether you’re looking at hardware, flashing, or a full unit.
FAQs
Expect 15 – 20 years on the unit and 8 – 12 years on the weatherstrip and sweeps in Antioch’s climate before they need attention. The Delta moisture pattern wears sills and flashing faster than the glass. Call (888) 419-3650 for a free inspection before small wear turns into a frame replacement.
Often yes. Hardware, weatherstrip, sweeps, and flashing repairs are common and usually run $400 – $1,800. Full replacement only makes sense when the frame, glass seal, or rough opening is compromised. Call (888) 419-3650 and we’ll tell you which side of that line you’re on.
A single unit is typically a few hours; a whole-house window package usually runs one to three days on site. Most hardware and weatherstrip repairs are done in a single visit. Call (888) 419-3650 to schedule a free estimate and we’ll give you a realistic timeline for your home.
We start with the label or etched code on the glass edge or sash, then measure the visible glass and rough opening to 1/16 inch. If the Tamko part is discontinued, we match OEM or a same-spec aftermarket equivalent and show you which one we’re using. Call (888) 419-3650 to schedule a free estimate.
Groundwork Construction Co. of Antioch also works with KraftMaid, Cambria, and Silestone on the interior side when a window project ties into a bigger remodel. If your Tamko part is failing and you want a straight answer on repair versus replacement, call (888) 419-3650 for a free estimate. You’ll speak to a live person, and our technicians bring up to 12 years of hands-on experience to the job.
Written by the team at Groundwork Construction Co. of Antioch, serving Antioch and nearby areas.