Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tremron Kitchen Remodeling: The Antioch Owner’s Guide
Tremron kitchen remodeling in Antioch typically runs $14,000 – $45,000 installed, and because our technicians have up to 12 years of experience, we can usually tell you within the same day what your failed part needs. Most Antioch homeowners discover the problem the same way: a cabinet door that won’t close flush, a drawer that grinds halfway out, or a hinge that snapped under the weight of a loaded shelf at 6 a.m. on a weekday.
You’re reading this because something on your Tremron kitchen has come loose and you want it matched right, priced honestly, and fixed without a mystery invoice. That’s exactly what this page is for.
Key Takeaways
- Tremron cabinet and door hardware follows specific series specs – the wrong part physically fits but fails early.
- Installed cost for a full Tremron kitchen refresh in Antioch falls in the $14,000 – $45,000 band, with small scopes at $9,000 – $20,000.
- We’re an independent Antioch service provider, not affiliated with Tremron, and we source OEM parts where they still exist.
- Every project is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right.
Which Tremron Models This Applies To
Tremron builds cabinet and door lines across a few naming families, and the part number you need depends on which one is inside your kitchen. The fastest way to identify yours is to open a cabinet door and look at the hinge plate stamp near the frame: it will list a series code and a mounting pattern, usually a two-screw or three-screw configuration. On drawers, slide the drawer out fully and read the glide manufacturer’s stamp on the underside of the rail – Tremron uses a couple of slide generations, and the mounting hole spacing changed between them by several millimeters on some runs. That’s the compatibility gotcha most homeowners miss: a replacement hinge or glide will screw into the same old holes and still throw the door out of alignment, because the offset on the newer part is different.
For Antioch kitchens, we recommend OEM where the part is still in production. When it isn’t, we spec a quality aftermarket equivalent that matches the mounting pattern and load rating rather than forcing a close-enough fit. We don’t stock parts and nothing lives on a truck, so we measure first and order correctly. If your kitchen also has KraftMaid, Cambria or Silestone elements, we handle those in the same visit.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tremron Kitchen Remodeling Is Failing
These are the five symptoms we hear about most often from Antioch homeowners, and what’s actually causing each one.
- A cabinet door that sags and won’t stay closed. The hinge plate has lost grip in the wood because the original screws stripped their holes – common in kitchens that see heavy daily use and summer heat cycling through the cabinet frames.
- A drawer that grinds or sticks halfway out. The glide’s nylon roller has worn flat or the rail has bowed. In Antioch’s dry summers and damp winters, wood drawer boxes move a little seasonally, and a marginal glide will start to bind.
- A soft-close feature that stopped working. The damper cartridge inside the hinge has failed. This is almost always a part-only replacement, not a full hinge swap, if you match the cartridge to the right series.
- A cabinet door that hangs crooked despite tightening. The frame has racked slightly or the hinge offset is wrong from a previous mismatched replacement. This is where a wrong aftermarket part does its damage – it fits, then pulls the door out of square.
- Popping or creaking when you open a drawer. The glide’s mounting screws have backed out from repeated cycling. Retightening helps for a while; eventually the screw holes need to be re-set or the glide replaced with one rated for the load.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Tremron kitchen work in Antioch sits in a clear band, and we quote it as a fixed line-item number so the figure you see is the figure you pay. Here’s what drives the range:
| Scope | Installed Range (Antioch) |
|---|---|
| Kitchen remodel, full scope | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What moves you up the band: cabinet count, whether your Tremron boxes can be saved or need refacing, countertop material choice (Cambria vs Silestone swings the number noticeably), and how much demo is involved. Parts-plus-labor is quoted transparently – you’ll see the hardware line separately from install. Every project carries the 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction, and we back it in writing.
DIY or Call Us?
Some checks are safe to do yourself: reading the hinge stamp, measuring your drawer glide spacing, and tightening a screw or two. Where DIY goes wrong is at the point of matching a replacement part to your Tremron series – most homeowners buy the wrong cartridge or glide online, install it, and discover the door racked or the drawer still binds within a week. That’s a $40 part and a wasted Saturday, not a safety risk, but it’s a real cost multiplier when it happens twice.
What we do differently is measure the series, order against the actual spec, and install in most cases on a single visit. If your kitchen is due for more than just parts, our upfront pricing keeps the whole scope clear from the start. Call (888) 419-3650 for a free estimate – a live person answers 24/7.
FAQs
Soft-close hinges and drawer glides typically hold up 10 – 15 years in regular use. Antioch’s dry summer air and damp winters speed up wear on dampers and nylon rollers, and we often see the first failures at year 8 – 10 in high-use kitchens.
Often yes. A soft-close cartridge, a hinge plate, or a single drawer glide can usually be swapped on its own rather than replacing all the hardware. We’ll tell you straight if repair is the better call for your Tremron series.
Most hardware replacements – a handful of hinges or glides – finish in a single visit, usually a couple of hours. Larger jobs involving cabinet installation or countertops run longer and get quoted by scope. Call (888) 419-3650 for a firm timeline.
We identify your series from the stamp on the hinge or glide, then order OEM where it’s still produced and a matched aftermarket equivalent when it isn’t. We don’t guess at compatibility, and we don’t carry parts on a truck – the right part gets ordered to your kitchen.
Written by the team at Groundwork Construction Co. of Antioch, serving Antioch and nearby areas.