Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Antioch: What the Job Actually Involves
An iron fence in Antioch is a fabrication job, not a pick-it-off-the-shelf job. Most residential runs land between $3,500 and $9,000, and a typical side-yard or front-yard install takes two to four working days on site once panels are fabricated and finished. That range covers a standard residential run with a man gate; long street frontages, tight alley access, and custom scrollwork push it higher. Call (888) 419-3650 and we’ll walk your property line with you and put a real number on paper.

Here’s what that number depends on, and how this work plays out on Antioch’s tight lots and inland lots alike.
How We Build an Iron Fence, Start to Finish
Every run goes through the same five stages. What changes is the time each one takes, and that’s driven mostly by access and by how much digging we can get done in one pass.
Day 1: Layout and utility check
Before anyone digs, we confirm the property line against your plat or survey, mark the exact post centers, and call in the 811 locate for gas, water, and the irrigation lines that run through older Antioch yards. This is where you decide the gate swing direction and which side faces the street. Get that wrong and you’ll live with it for twenty years. We also note the fence height you’re after, usually 4 to 6 feet for a residential iron run, and whether the design is an open picket style or a solid-panel privacy build.
Day 2: Post holes and concrete footings
Iron posts need a real footing, not a shovel and a bag of quick-set. We set posts in concrete at a depth that clears the frost line and stays put through the seasonal soil movement. This is the longest single stage on a big run, and on clay-heavy lots it’s where the schedule can flex. Post spacing is typically 6 to 8 feet on center. You’ll decide the post caps and finials at this stage if you haven’t already.
Day 3: Fabrication and panel setting
Panels arrive cut, welded, and powder-coated at the shop, so site time is assembly, not cutting steel. We hang the panels level, set the gate, and true the latch so it closes with one hand. If you chose galvanized-and-painted over powder coat, that finish decision was locked in weeks earlier because it sets the lead time.
Day 4 (or later): Gate hardware and finish
Gate closer, hinges, latch, and any automation go on. A rolling-code remote or a keypad entry on a driveway gate gets wired and tested here. You’ll pick the hardware finish ahead of time, so this is install, not a decision point.
Final: Walkthrough and punch list
We walk the run with you, check every post for plumb, every panel for level, every gate for swing, and hand over the written terms of our 730-Day Done Right Promise. If something isn’t right, it gets fixed on us.
Your homeowner decisions cluster early: layout and gate swing on day one, finish and hardware before fabrication, and nothing major during install. That’s deliberate. We don’t want you making choices mid-pour. If the iron fence is part of a full Fence Installation in Antioch scope, we sequence the iron with the rest so the whole perimeter goes in as one coordinated job rather than three disconnected visits.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Weigh Before We Weld Anything
Iron and steel fencing isn’t one product. The choices below are the ones that actually change price, longevity, and how the fence feels on your property.
- Wrought iron vs. steel: Traditional wrought iron is forged and heavy, and it costs more. Steel is the practical choice for most Antioch homes: strong, weldable, and it takes a powder coat cleanly. It suits the security-first buyer.
- Powder coat vs. galvanized + paint: Powder coat is a baked finish, harder and more uniform, and it’s the low-maintenance pick. Galvanizing protects the steel from rust from the inside out; painted galvanized runs are durable but need touch-ups over the years.
- Height and picket spacing: 4 feet reads as a boundary marker. 5 to 6 feet with tighter picket spacing is what people choose when the fence is doing security duty. Narrow gaps keep pets in and unwelcome entry out.
- Gate automation: A driveway gate with a rolling-code remote and keypad is the upgrade most security-minded homeowners ask about. Budget for the operator, the hardware, and a low-voltage run to the gate.
- Aluminum as a value alternative: Lighter, rust-proof, cheaper, and it looks close to iron from the street. It won’t take the same impact. If security is the reason you’re building, iron is the answer.
We don’t lock you into one material family. Where hardscape meets the fence line, our Belgard and Techo-Bloc paver work pairs cleanly with iron posts, and the Patios, Walkways & Pool Decks in Antioch work we do on the same properties is often drawn in the same pass so the grades and edges line up.
What an Iron Fence Costs in Antioch, CA
$3,500 to $9,000 is the working range for a residential iron fence in Antioch. Below that, you’re looking at a short run or aluminum. Above it, and you’re into long frontages, heavy custom fabrication, or gate automation.

Five things move the number:
- Linear feet: The biggest lever. More panels, more posts, more footing, more labor.
- Access: Alley-load lots and tight townhome side yards mean material handling takes longer. If we can’t back a truck to the line, that shows up in labor.
- Finish: Powder coat costs more up front and lasts longer. Painted galvanized costs less and asks for maintenance.
- Gates: A pedestrian gate is modest. A driveway gate with automation is a real line item.
- Site conditions: Old concrete, roots, and buried utilities all add time to the dig.
A written estimate from us is line-itemed: posts, panels, finish, hardware, concrete, and labor, each with its number. What’s not included unless we say so: removing an old fence, stump grinding, and any repair to irrigation we cut during the dig. What’s always included: the 730-Day Done Right Promise, and upfront pricing so the number on the page is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhy Antioch Lots Make This a Different Job
Antioch sits on the Delta at the foot of the East Bay hills, and that shapes everything about how we set posts. The flats carry 1950s to 1970s ranch tract homes and older downtown stock with original slabs and clay-heavy soils; the southern hills hold 1980s to 2000s subdivisions on different grades. Those clay soils swell and shrink with the seasons, so a post that’s shallow-set in July will heave by the next wet winter. We set deeper and pour heavier because of it. Along the riverfront and downtown blocks, the water table runs high, and footing holes can fill with groundwater before they’re poured, which is exactly the kind of thing we plan for rather than discover.
The Delta winds do their part too. Afternoon gusts off the San Joaquin drive dust and load every panel, so picket spacing and post spacing get chosen with wind in mind, not just looks. Hot dry summers and cold fog-influenced winters mean we pour early in the day and cover footings against fast drying. Alley-load lots and tight townhome setbacks are common here, so we route material in on a plan rather than improvising. We work Antioch properties every week and know the block-by-block reality. Permits and HOA rules vary by subdivision, and we’ll tell you plainly when a run over a certain height or a street-facing design needs a sign-off before we build.
Serving Antioch, CA – Our Local Coverage Area
We serve Antioch and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Iron Fence in Antioch
Most residential runs are done in two to four working days on site. Fabrication lead time for powder-coated panels adds a couple of weeks ahead of that, so the full calendar from order to finish is usually a few weeks. Call (888) 419-3650 for a schedule based on your line length.
Low residential fence runs often don’t need a permit, but height, location, and street-facing design can change that, and HOA rules layer on top. We check your specific situation before we build. Call us and we’ll tell you what your lot requires.
Usually yes. Post holes are point digs, not trenching, and we plan the post spacing around established plants and trees. It costs less than a full reset, and staging it as part of a full Fence Installation plan keeps the disturbance contained. Call (888) 419-3650 to walk it with us.
Residential iron fence runs typically land between $3,500 and $9,000, with linear feet, finish, gates, and access being the main drivers. We’ll give you an exact line-itemed number on a free estimate. Call (888) 419-3650 to schedule one.
Workmanship is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. If something we installed isn’t right, we make it right. Call (888) 419-3650 to talk through the terms before you commit.
Homeowners adding a rear yard, a driveway gate, or a new structure to enclose often pair this with scope from ADU Design & Permitting in Antioch, and we sequence the two so the fence doesn’t get built around a future trench line.
Get an Iron Fence Estimate in Antioch
Call (888) 419-3650 for a free on-site estimate. A live person answers that line, any hour. On the call, we’ll set a time to walk the property line, confirm your gate swing and finish, and send a written line-itemed quote with the price locked. No voicemail, no waiting, no change orders once the work starts. Upfront pricing, 730-Day Done Right Promise, built to last.
Written by the team at Groundwork Construction Co.