Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
What an Iron Fence in Brentwood, CA Actually Involves
An iron fence in Brentwood typically costs $3,500 – $9,000, and most residential runs are finished in three to five working days once the layout is approved and the permit is in hand. The job means laying out posts along your property line, digging and setting them in concrete below your frost-safe depth, then finishing with panels, gates, and a protective coating. Call (888) 419-3650 and we’ll walk your lot and give you a written, line-item number before anyone lifts a shovel.

How We Build an Iron Fence in Brentwood, Start to Finish
An iron fence isn’t a fence you can throw up in an afternoon. The posts are the structure, and if they’re set wrong the whole run sags within a season. Here’s the actual sequence we follow on a Brentwood property.
Day 1 – Walk, layout, and utility locate. We confirm the property line against your plat, mark the run, and have the underground utilities located before a single post hole gets dug. On former orchard parcels around Brentwood this step matters more than it does most places; we’ve hit old irrigation lines and furrow remnants on lots that looked clean from the street. You decide the final fence height, the gate positions, and where the line sits relative to your setback. We submit the permit paperwork at this stage if the town requires one.
Day 1 to 2 – Demolition and site prep. If there’s an existing fence, it comes out now, and we haul it off. We clear the line, trim back anything overhanging, and set grading so water still drains away from your slab or footing pads. On an empty lot this is often the quickest part – a half day on a clean 150-foot run.
Day 2 to 3 – Post setting. This is the stage that decides whether your fence stays straight. Posts get set in concrete, plumbed and braced, and left to cure. We don’t hang panels on green concrete just to save a day. You’ll see the stakes and lines sitting there overnight, and that’s exactly what should happen.
Day 3 to 4 – Panels, gates, and coating touch-up. Panels get attached, gate hardware is hung and adjusted, and we go around the whole run touching up any coating nicks from installation. You get a walkthrough here, and anything that’s not flush or swinging right gets corrected before we pack up.
Day 4 to 5 – Final inspection and walkthrough. If your project required a building permit, we meet the inspector and get sign-off. Then we walk the finished fence with you, hand over care instructions, and confirm the finish coat.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Pick Between
Most of your decisions come down to how the metal is made and how it’s protected. Here’s the honest read on each.
- Wrought iron (solid bar, welded, traditionally forged pieces): The heaviest, longest-lived option, and the one that genuinely lasts generations when it’s galvanized and repainted. It’s also the top of the price range, and it needs periodic recoating in our sun.
- Ornamental steel (tube or solid bar, powder-coated): The most common choice for a residential yard here. Strong, clean lines, and a factory powder coat that holds up well against the Delta wind. Expect it mid-range in the $3,500 – $9,000 band depending on run length.
- Aluminum (cast or tube, powder-coated): Lighter and rust-free, easier to move, and often the budget-friendly path. It dents where steel would hold, so it suits shorter decorative runs and side-yard fencing more than a long front boundary.
- Finish choices: Powder coat is the standard for color and durability. Hand-applied paint gives you a richer look and easy touch-ups, but you’ll be refreshing it. Galvanizing under the finish is what stops the rust from starting at the welds.
- Configurations: Picket spacing, post size, height (3 ft, 4 ft, and 5 ft are the typical residential calls), and gate hardware. A single walk gate with a self-closing hinge and a matching driveway gate are the two add-ons most Brentwood owners ask about.
We don’t sell you a fence that’s the wrong metal for your exposure. Call (888) 419-3650 and we’ll sketch the real trade-offs on your lot, not on paper.
What an Iron Fence Costs in Brentwood, CA
Our lead range for a residential iron fence in Brentwood is $3,500 to $9,000, with most typical runs landing somewhere in the middle. Where you land depends on the variables below.

What pushes a job toward the high end: a long boundary line (200 feet and up), a solid wrought-iron build rather than ornamental steel or aluminum, a grade that changes across the run so posts need reinforcing, one or more gates with matching hardware, and demo of an old fence plus haul-away. The expansive clay soils here and the need to set posts below the active zone can add labor on tricky lots.
What keeps it near the low end: a shorter run, ornamental steel or aluminum, a flat and already-cleared line, and no gate.
Your written estimate from us itemizes post count, panel type, finish, gates, hardware, demo, and any permit fees, so you see exactly what each line costs. What’s typically not in the base number: heavy site grading, replacing a damaged retaining wall along the line, and any landscape repair after installation. We’ll flag those upfront – the number you see is the number you pay, and we back every job with our 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Brentwood Homes Do to This Job
Brentwood’s housing stock is overwhelmingly new – large tracts of 1990s through 2020s Spanish and Mediterranean stucco homes, plus custom ranchettes on multi-acre lots and a small pocket of older downtown bungalows. That shape of neighborhood changes the iron fence job in specific ways. In the newer subdivisions, HOA rules on fence height, color, and picket style are active, and we check those before anyone draws a line. On the multi-acre parcels out in the orchard country, the property line often runs through expansive clay and old furrow lines, and we’ve pulled buried irrigation pipe and dealt with residual dark soil from the agricultural past. The hot inland summers and persistent Delta winds accelerate stucco cracking and foundation movement, so footings get extra attention to the active clay zone. The town’s grading and drainage rules also mean we tie fence installation into how your lot sheds water, and lot improvements often get bundled – a fence is commonly paired with a new patio or walkway via our Patios, Walkways & Pool Decks in Brentwood team.
Serving Brentwood, CA – Our Local Coverage Area
We serve Brentwood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Brentwood
Allow three to five working days for a typical residential run, plus a week or two upfront for permit approval if your project needs one. Larger runs or custom wrought iron extend that. Call (888) 419-3650 for a job-specific timeline.
Often yes, especially for taller fences or ones along a setback or corner lot. We confirm the requirement with the town of Brentwood and pull the permit for you. Call (888) 419-3650 and we’ll tell you what your specific lot needs.
Yes – we have the underground utilities located before we dig, so we know where your irrigation and electrical runs are. If the layout needs to shift a foot to miss a line, we shift it. Call (888) 419-3650 to set up a walk of your property.
Residential iron fence runs $3,500 – $9,000, depending on length, iron type, gates, and demo. Ornamental steel and aluminum typically sit lower in that range; solid wrought iron sits higher. Call (888) 419-3650 for a precise quote – estimates are free.
Every fence we install is covered by our 730-Day Done Right Promise – if it isn’t done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space. Call (888) 419-3650 to talk it through.
Get a Free Iron Fence Estimate in Brentwood
A free on-site estimate for your iron fence starts with a walk of the property line, a look at your grade and soil, and a conversation about iron type, gates, and finish. You’ll get a written, line-item quote – no pressure, no vague “it depends.” Call (888) 419-3650 to schedule yours. Considering the wider project? Our Fence Installation in Brentwood covers the full scope.
Written by the team at Groundwork Construction Co.