Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Clayton, CA: What It Costs and How Long It Takes
A tub-to-shower conversion in Clayton runs $3,500 to $10,000 for most homes, and a typical job is finished in 10 to 18 working days once demolition starts. That range covers swapping a seldom-used tub for a walk-in shower in the same footprint. If the new shower needs a relocated drain, new valves, or a structural fix behind the wall, expect the high end. Call (888) 419-3650 to schedule a free on-site estimate before you decide anything.

How We Run a Tub-to-Shower Conversion, Stage by Stage
Every conversion follows the same order of operations, and the order matters. If someone quotes you a shower install without a real inspection step, you’ll want to know what’s being skipped.
Stage 1: Measure, tear-out, and a look inside the wall (1 – 2 days)
We pull the tub, the surround, and the valve trim. Then we open the wall at the valve so we can see what’s actually there. In Clayton ranch homes from the 1960s and 70s, this is where we find lead or galvanized supply lines, rotted subfloor from a slow leak, and sometimes framing that needs sistering. You decide here whether those repairs are in scope. We don’t bury them and surprise you later.
Stage 2: Rough plumbing and electrical (2 – 3 days)
The drain gets re-centered for a shower, the valve gets replaced with pressure-balance or thermostatic trim, and we add blocking for grab bars and a bench if you’re planning either. If a permit is required, this is the stage the inspector checks, so we schedule it before anything closes up.
Stage 3: Waterproofing (2 days)
This is the part that decides how long the shower lasts. We build a sloped pan, install a bonded waterproofing membrane, and band the corners and seams. Schluter’s Kerdi system is what we use most often because the waterproofing bonds directly to the substrate instead of sitting behind a cement board that can wick moisture. You’ll see it before tile goes up.
Stage 4: Tile and fixtures (4 – 6 days)
Wall tile, floor tile, curb, niche, then trim. This stage always takes longer than homeowners expect, and it’s the one you’ll want to spend your decision time on early: tile size drives labor cost, and large-format panels cost more to set than a standard field tile.
Stage 5: Glass, trim-out, and walkthrough (2 – 3 days)
Glass gets templated and installed, the valve trim and shower head go on, and we caulk and seal. We test the drain and check the shower pan holds water. Final walkthrough happens the same day, and the 730-Day Done Right Promise starts there.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
- Shower pan vs. a site-built tiled floor: a molded pan like a Sterling is faster and cheaper by roughly $400-$900, and it’s easier to clean. A tiled floor with a linear drain gives you a flush entry and a more custom look but adds tiling and prep labor.
- Framed vs. semi-frameless glass: framed glass keeps the budget in check. Semi-frameless costs meaningfully more and shows less metal, which tends to matter when the bathroom is visible from a bedroom.
- Tile grade: porcelain holds up to daily shower spray better than natural stone, and it doesn’t need annual sealing. Stone looks warmer but wants sealing and is more slippery when wet.
- Fixtures: a Toto or Grohe valve and trim set is worth the upcharge when you’re already opening a wall. Cheaper trim fails at the cartridge first, and replacing a cartridge later costs a service call.
- Bench, niche, and grab-bar blocking: each is a small add, but they’re far cheaper done now during framing than added afterward.
- Height and reach: if the household includes anyone shorter or older, a lower valve height and a hand-held on a slide bar changes how the shower works day to day.
What Tub-to-Shower Conversion Costs in Clayton, CA
Most Clayton conversions land between $3,500 and $10,000. Where you fall in that range depends on a short list of variables, not on your taste in tile alone.
- Footprint and access: the tighter the bathroom and the further the path from the front door, the more labor the demo and material hauling take. A second-floor bathroom or a narrow stair adds time.
- What’s behind the wall: old galvanized supply lines or a rotted subfloor push a job toward the top of the range by $800-$2,500.
- Moving plumbing: keeping the drain where it is saves real money. Relocating it within the room adds a few hundred to a couple thousand depending on the slab or framing.
- Material grade: standard porcelain and a molded pan sit near the bottom. Stone, a tiled linear drain, and semi-frameless glass sit near the top.
- Permit scope: a shower swap that keeps plumbing in place and was already permitted as a bath may need only a limited inspection. New plumbing lines or structural work broaden the permit and add cost.
A written estimate from us is line-item: tear-out, rough-in, waterproofing, tile, glass, fixtures, permit, and disposal, each with a number. What it doesn’t include is anything we can’t see until the wall is open. We quote that as an allowance with a cap, so the price you see is the price you pay. 0% financing for 18 months is available, and projects over $10,000 get $1,000 off.

See the difference
Before
After
Before
After
Before
AfterWhat Clayton Homes Specifically Do to This Job
Clayton’s housing stock shapes this conversion more than most homeowners expect. In the flat core you’ll find mid-century ranch homes where the original tub is set into a plaster-and-lath wall, and pulling it out means patching and retiling a larger section than you planned. On the steep lots above town, you get 1980s through 2000s custom homes where the bathroom sits over a raised foundation and the plumbing chase runs behind an exterior wall. Those two situations price differently, and we look at which one you have before quoting. Steep hillside lots also mean material has to come up driveways and stairs that make delivery slow, and we plan for it in the schedule.
Permitting in Clayton runs through the city, and inspection timing is the variable that most often stretches a conversion here. We pull permits and schedule inspections before closing up walls so nothing gets tiled over and re-opened. If you’re also considering exterior work on the same house, homeowners often pair this with Metal Roofing in Clayton or Tile Roofing in Clayton, and it’s worth bundling the site visits. If the conversion is part of a larger project, our Bathroom Remodeling service covers the wider scope, and you can read the full Bathroom Remodeling in Clayton page for that. We work throughout Clayton and the ZIP 94517 area.
Serving Clayton, CA – Our Local Coverage Area
We serve Clayton and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Tub-to-Shower Conversion in Clayton
Plan on 10 to 18 working days from demolition to walkthrough, and add a week if a permit inspection falls over a holiday. A straightforward swap in the same footprint with stock materials runs close to 10 days. Tile-heavy jobs with custom glass land closer to 18. Call (888) 419-3650 and we’ll give you a real schedule for your bathroom.
Usually yes when plumbing is being altered, and often no when it’s a like-for-like fixture swap in the same location. The permit question depends on what changes behind the wall, so it gets answered during the estimate, not on the phone. We pull the permit and handle inspection scheduling when one is required.
Yes, and most of the time that’s the right call. If the drain stays put and the framing is sound, the job stays simpler and cheaper, often closer to the $3,500 end of the range. We only recommend moving plumbing when the current layout makes the shower unusable or unsafe. Call (888) 419-3650 for an exact quote, and estimates are free.
Most Clayton homeowners pay between $3,500 and $10,000, with material grade, hidden wall damage, and permit scope moving the number. Add-ons like a bench, niche, or grab-bar blocking are small individually but add up. Call (888) 419-3650 for a line-item written estimate at no charge.
Every conversion is covered by our 730-Day Done Right Promise: if the workmanship fails, we come back and make it right. That covers the installation, waterproofing, and tile work we perform. Product warranties come from the fixture and membrane manufacturers separately, and we hand you those documents at walkthrough. Our technicians have up to 12 years of experience on this kind of work.
Get a Free Estimate for Your Conversion
Call (888) 419-3650 to schedule a free on-site estimate for your tub-to-shower conversion in Clayton. A live person answers around the clock, including evenings and weekends. We’ll measure the bathroom, open the valve wall if needed, and hand you a line-item written quote with a schedule. No pressure to sign on the spot, and no change orders later. Background-checked, uniformed technicians arrive for every visit.
Written by the team at Groundwork Construction Co. of Antioch.