Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Bay Point: What They Cost and How Long They Take
Custom & geometric windows in Bay Point usually run $800 to $4,500 per opening for the window itself, with whole-home geometric packages landing in the $8,000 – $25,000 range once framing work and county permits are included. Most single-window jobs are measured in week one, fabricated in three to five weeks, and installed in a day or two. Call (888) 419-3650 and we’ll set a free on-site estimate so you get a real number for your wall, not a ballpark.

How the Job Actually Runs, Stage by Stage
Custom and geometric windows are not a stock swap. A trapezoid, an arch-top, a half-round over a slider, or a triangular gable window has to be built to the opening as it exists, which means more measuring, more lead time, and one more set of eyes before anything is ordered. Here’s the sequence we run.
Day 1: Measure and template. We come out and template the actual opening, not the drawing. Arched or angled openings are rarely square after decades in a mid-century Bay Point home, so we check the frame for racking, note where stucco or siding meets the trim, and confirm the rough opening dimensions. You decide the glass package and the frame material at this stage, because both affect the price and the fabrication window.
Week 1 – 2: Permit through Contra Costa County. Bay Point is unincorporated, so the permit goes through the county rather than a city building department. Structural changes, new openings, and egress windows need a permit; a straight replacement into an existing frame sometimes doesn’t, and we’ll tell you which side of that line your job sits on before you spend anything. You sign off on the scope and the written quote here.
Week 2 – 6: Fabrication. Custom geometric units are built to order. Standard shapes take about three to four weeks; true custom arch tops and radius windows with specialty glass run five to six. You lock in the final spec sheet and the glass selection during this window, and we don’t order until you’ve signed it.
Installation days: Demo, prep, set. Most single-window installs happen in one day. Multi-window packages run two to three days. We pull the old unit, inspect the framing for rot or soft sill plates (common behind old metal windows), flash and seal the opening, set the new window plumb and square, insulate the gap, and trim it out. Geometric units get shimmed and checked for square at every corner because a trapezoid that’s half an inch off shows it.
Final walk and inspection. We run the windows, check the seal, water-test the flashing if the new window cuts into the wall, and coordinate the county inspection where one is required. You get the warranty paperwork and a walkthrough before we pack up.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Custom geometric windows give you more choices than a stock replacement, and each one moves the price and the long-term performance. Here’s what you’re actually deciding.
- Frame material: vinyl vs. fiberglass vs. wood-clad. Vinyl is the most economical and holds up fine in Bay Point’s wind and sun, but it’s limited in how tight a radius it can bend. Fiberglass handles tighter curves and moves less with temperature, at a premium. Wood-clad (Andersen and Marvin both build to custom shapes) gives you the look of painted wood inside with a weather-resistant exterior, and it’s the choice when the window is visible from the living room as a design feature.
- Glass package. Standard insulated glass is the baseline. Low-E and argon fill help with the delta’s afternoon heat and are worth it on large south- and west-facing geometric units. Tempered glass is required where the window is close to a floor or a door.
- Shape and configuration. Arch tops, half-rounds, trapezoids, triangles, and radius corner units all fabricate differently. Simpler curves cost less and lead time is shorter; a true eyebrow arch with a custom radius is a specialty order.
- Finish and trim. White or tan interior trim is standard. Stained wood and custom exterior colors add cost, and long-lasting factory finishes beat field-painted ones over time.
- Hardware. Casement cranks, awning operators, and screen options. You’ll want screens rated for wind on the exposed sides of the house.
What Custom & Geometric Windows Cost in Bay Point, CA
Per-window custom geometric units in Bay Point typically land between $800 and $4,500, and a package of several shaped windows across the front of a home usually runs $8,000 to $25,000. Here’s what separates a job at the low end from one at the high end.
| Line item | Typical range |
|---|---|
| Single custom geometric window (supply & install) | $800 – $4,500 |
| Whole-home geometric package | $8,000 – $25,000 |
| Contra Costa County permit (new opening or structural) | Included in written quote |
Four things push a job up or down. Size and shape complexity is the biggest: a standard arch top is far cheaper than a custom radius. Existing condition matters more than buyers expect. If the framed opening is rotted behind the old window, you’re paying for repair before the new one goes in. Material grade runs vinyl at the low end and wood-clad at the high. Permit scope depends on whether you’re replacing an existing window or cutting a new opening, and that’s the single biggest swing in total cost.

Our written estimate lists the window units, labor, disposal, flashing and sealant, and the permit. It doesn’t cover structural repair uncovered during demo, unexpected rot, or interior wall touch-up. We price those separately if they come up so there are no surprises. The 730-Day Done Right Promise covers the installation workmanship for two full years, if it’s not done right we make it right.
See the difference
Before
After
Before
After
Before
AfterWhat Bay Point Homes Do to This Job
Bay Point sits on the edge of the Sacramento-San Joaquin Delta, and that matters here more than in a typical East Bay town. The delta winds beat on exposed walls and roofs all spring, so exterior flashing, sealant, and wind-rated glass carry more weight on a Bay Point install than they would ten miles inland. Much of the housing stock dates to the post-WWII and mid-century tract era, and the framed openings in these older single-story homes rarely come out square. We routinely find soft sill plates, out-of-plumb jamb framing, and original metal windows that have been sealed shut for decades. On the newer infill side, homes tend to have more uniform framing and modern windows already, so those jobs lean toward glass upgrades and a design matching on the geometric units. Because the community is unincorporated, the permit goes through Contra Costa County, not a city building department, which means a slightly different inspection calendar and paperwork than homeowners who’ve only built inside Pittsburg or Concord expect. We handle that process so you don’t end up calling the county in circles.
Serving Bay Point, CA – Our Local Coverage Area
We serve Bay Point and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Custom & Geometric Windows in Bay Point
Most single custom geometric windows are fabricated in three to five weeks and installed in a single day; whole-home packages take two to three install days. The lead time is the fabrication, not the install, so plan on roughly four to six weeks from signed estimate to final walk. Call (888) 419-3650 for a realistic timeline on your specific window.
If you’re cutting a new opening, changing the size, or adding an egress window, yes, and the permit goes through Contra Costa County. A straight replacement into an existing framed opening often doesn’t need one. We’ll confirm which applies to your job during the estimate and pull the permit for you if it’s required.
In most cases yes. If the window is going into an existing opening the same size, the framing stays put. If the opening changes size or the wall holds a structural header, some framing work is part of the job. We map that out at the measure, not mid-install.
Roughly $800 to $4,500 per custom geometric window, or $8,000 to $25,000 for a whole-home package. Material, shape, and whether a new opening requires a permit move the total most. Call (888) 419-3650 for an exact quote, the estimate is free and comes in writing with line items.
The installation carries our 730-Day Done Right Promise for two years of workmanship, on top of the manufacturer’s warranty on the window unit itself. Call (888) 419-3650 and we’ll walk through what’s covered and for how long before you sign anything.
Get a Free Estimate on Custom & Geometric Windows in Bay Point
If you’re planning a shaped window, an arch top, or a full geometric package for your Bay Point home, the next step is a free on-site estimate. We measure your actual openings, show you material and glass options, and put a written line-item price in your hands. Call (888) 419-3650. A person answers, and if this is part of a bigger window project, our Windows & Doors in Bay Point page covers the full scope.
You may also want to see the wider Windows & Doors work we handle, check what else we do across Bay Point, or consider groundwork that homeowners often pair with a window refresh: Concrete Driveways & Concrete Work in Bay Point and Asphalt Driveways & Resurfacing in Bay Point.
Written by the team at Groundwork Construction Co.