Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Fence Repair in Danville, CA: What It Takes and What It Costs
Fence repair in Danville typically runs $3,500 – $9,000 depending on how many linear feet are failing, whether posts have to be reset or replaced, and how much of the structure can be salvaged versus rebuilt. Most repairs run two to four days on site once material is staged. Call (888) 419-3650 to schedule a free assessment; we give you a written, line-item quote before any crew touches your fence line.

How We Work a Fence Repair in Danville, Start to Finish
Repairs on acreage and large-lot properties don’t follow the same playbook as a tract-home fence. Here’s the actual sequence we run.
Stage 1: Walk and mark (day one, roughly 60 – 90 minutes). We walk the full fence line and mark every failing post, broken rail, split board and footing that’s heaved. On larger Danville lots this often means checking sections the homeowner hasn’t looked at in years. You decide right then how much of the line you want fixed versus left for a later phase.
Stage 2: Footing and post assessment (day one, add an hour on long runs). A fence post is only as good as what’s under it. We probe footings and check for rot at the soil line, which is where most failures start. You get a straight answer on which posts can be reset with new concrete and which ones are gone.
Stage 3: Demo and prep (day one into day two, four to eight hours). We pull the failed boards, cut out broken rails, and remove posts that can’t be saved. Debris gets hauled the same visit. This is the messy stage, and it’s the one that most surprises people on a long perimeter: the number of fasteners you’ll need tells you how much of the fence is genuinely sound.
Stage 4: Rebuild and reset (day two into day three, one to two days). New footings cure, posts get set, rails and boards go back on, and we match the existing profile and stain tone as closely as the stock allows. Matching old weathered cedar or redwood with new material takes a test board first so the repair doesn’t read as a patch.
Stage 5: Final walk (day three, 30 minutes). We walk the line with you, check gate swing and post plumb, and hand over the written workmanship coverage. If a fitting, latch or board isn’t right, we come back and fix it under the guarantee.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make on a Repair
Most of the decision-making on a repair comes down to how far you go. A few honest trade-offs:
- Patch-and-match vs. replace the run: Patching a single span is the cheapest path and keeps a mature fence intact, but new boards against 15-year-old weathered stock will read as a visible repair unless we stain to match. Replacing a whole run costs more but gives you a uniform look and a fresh lifespan.
- Post material: Pressure-treated pine is the workhorse and holds up well in the dry Tri-Valley heat. Cedar resists rot and takes stain beautifully but costs more. Steel posts cost the most up front and outlast both, which makes sense on the wind-exposed hillside lots.
- Board grade and thickness: Thinner stock is what fails first in summer sun. Stepping up a grade adds cost but buys years.
- Fasteners and hardware: Stainless or coated fasteners cost more than standard and are the difference between a repair that lasts and one that rusts out in a few seasons.
- Finish and stain: A quality penetrating stain protects against UV and is one of the biggest levers on how long the repair holds.
If your repair has grown into a full-line project, that’s a different conversation, and our Fence Installation service covers the wider scope. We also handle Fence Installation in Danville when a repair is really the front half of a rebuild.

What Fence Repair Costs in Danville, CA
Repairs on Danville properties land between $3,500 and $9,000 in most cases. Where you fall on that range comes down to five things:
- Linear feet affected. A short run of board replacement sits near the low end; a full perimeter rebuild with new posts pushes toward the top.
- Existing condition. Rotted footings, heaved posts or termite damage raise labor significantly versus pulling a few split boards.
- Access and length. Acreage and hillside lots with a long fence line take more crew hours to reach and work than a compact urban yard.
- Material grade. Standard pressure-treated vs cedar or steel posts, and fastener grade, move the number.
- Permit scope. Minor repairs usually don’t need a permit; taller fences, work in fire-hazard zones on the 94506 side, or anything near a property line may. We handle the paperwork when it applies.
A written estimate itemizes linear footage, post count, material grade, and haul-away. It doesn’t cover unexpected rot found mid-repair or a hidden footing failure, which is why we flag those at the walk. Upfront pricing, no surprises: the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Danville Homes Specifically Do to This Job
Danville is a built-out, high-value Tri-Valley suburb. Almost everything here is repair, rebuild or remodel on an existing lot, not new construction, and that changes fence work. Homes are often 1960s through 1990s custom and semi-custom single-family builds on large lots, so we’re matching mature materials and older framing rather than fresh tract dimensions. The work splits in two: the flat, established 94526 core, where fences back mature landscaping and pools, and the hillside 94506 side around Blackhawk and Tassajara, where the WUI fire exposure and the dry inland heat put a heavier beating on wood and drive fire-resistant detailing. That summer sun is the failure mode we see most: UV-baked boards, posts drying out and splitting at the soil line, and fasteners rusting through. If your repair is part of a bigger property plan, homeowners often pair this with ADU Design & Permitting in Danville to sort out setbacks and property lines before we touch the fence.
Serving Danville, CA – Our Local Coverage Area
We serve Danville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Fence Repair in Danville
Most repairs run two to four days on site once material is staged. A small patch can wrap in a single day; a full line rebuild with new footings takes longer. Call (888) 419-3650 for a timeline on your specific line.
Minor repairs to existing fences usually don’t require a permit. Anything taller, near a property line, or on the fire-prone 94506 side may need one, and we handle that filing. We confirm the requirement at the estimate so there are no surprises.
Yes, in most cases. We reset and replace only the failing sections and match the existing profile and stain. If a run is past saving, we’ll tell you straight rather than patch something that won’t hold.
Most repairs fall between $3,500 and $9,000, depending on linear feet, post condition, material grade and access. Call (888) 419-3650 for an exact written quote; estimates are free.
Every repair is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction, and it’s in writing.
Get a Free Fence Repair Estimate in Danville
Call (888) 419-3650 to schedule a free on-site estimate for your fence repair in Danville. A live person answers around the clock, and we’ll set a time that works. Our technicians assess the line, flag what can be saved, and hand you a written, itemized quote with fixed pricing. Background-checked, uniformed technicians on every visit. We cover Danville and the surrounding area, and homeowners often pair a fence fix with a Garage Conversion ADU in Danville when a property is being reworked anyway.
Written by the team at Groundwork Construction Co.