Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Kitchen Remodeling: The Antioch Owner’s Guide
We install Dvele-compatible kitchen remodeling in Antioch, and most full kitchen projects run $14,000 to $45,000 installed, with cabinet-only work starting around $4,000. Dvele kitchens tend to be modular: the cabinet boxes, drawer fronts, and integrated panels are a matched system, and when one piece fails the damage usually shows up at a seam, a hinge line, or a toe-kick before the owner realizes what broke. In Antioch we see this most often after a hot, dry summer followed by a wet winter, when engineered panels move and the first soft spot appears under a sink or along a cabinet run facing an exterior wall. By the time it’s visible, the panel behind it is usually compromised too.
Key Takeaways
- Full kitchen remodel in Antioch: $14,000 to $45,000 installed.
- Dvele parts are system-matched, so the exact door, panel, or hinge series matters.
- We’re independent of Dvele and source compatible replacements, not factory-direct.
- Every project carries the 730-Day Done Right Promise.
Which Dvele Models This Applies To
Dvele builds a limited set of kitchen systems, and the parts aren’t interchangeable across them. Before we quote anything, we identify your specific cabinet and hardware series by measuring the door thickness, opening the cabinet and reading the hinge plate stamp, and checking the toe-kick panel for a manufacturer label. The most common mistake Antioch homeowners make is measuring the door face only and ordering a replacement that’s 3mm off on thickness, which means the hinge won’t sit flush and the door binds on the adjacent run. That 3mm tolerance is the compatibility gotcha on many Dvele cabinet fronts: the system expects a precise thickness, and a “close enough” panel won’t close cleanly.
On the OEM-versus-aftermarket question, we’re straight with you. Original Dvele parts are the cleanest match when they’re available, but lead times can run weeks on discontinued panel styles. A quality aftermarket equivalent in the same thickness and finish is often the smarter call for a partial repair, and we’ll tell you which way makes sense for your model and your budget. We also service KraftMaid, Cambria, and Silestone kitchens, so if you’re blending a new island or countertop into a Dvele framework, we can match it. We’re an independent provider and not affiliated with Dvele.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Dvele Kitchen Remodeling Is Failing
Most owners discover the problem when a door stops sitting level, a drawer sticks, or they spot discoloration at the base of a cabinet. Here’s what each symptom usually points to:
- Door hangs crooked or rubs the frame. That’s a hinge fatigue or plate-screw failure, usually at the top hinge where the load concentrates. In Antioch’s inland heat, the door face can also cup slightly, which compounds the misalignment.
- Drawer sticks near the back. Typically a worn slide or a sagging box, not a track alignment issue. Engineered drawer boxes react to humidity swings, and once the box racks out of square, no amount of adjustment fixes it.
- Soft or bubbling spot under the sink. Water intrusion into the panel substrate, often from a slow supply-line drip that goes unnoticed for months. The veneer hides the damage until the core is already swollen.
- Delaminating finish along a cabinet run on an exterior wall. Condensation and thermal cycling. Dvele’s engineered finishes hold up well, but a wall with poor insulation will stress any panel over time.
- Loose or failed toe-kick and end panels. Adhesive or fastener failure at the base, common where the kitchen floor has shifted. Small gap opens, moisture gets in, panel fails from the bottom up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the honest Antioch pricing on the work our parts page covers:
| Project | Installed Range |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
The range is driven by cabinet count, whether we’re replacing a single door run or reworking the whole layout, material tier, and whether plumbing or electrical has to move. You get parts plus labor on one upfront price, and your project is covered by the 730-Day Done Right Promise. The number you see is the number you pay.
DIY or Call Us?
You can safely swap a single drawer slide or tighten a loose hinge plate yourself, and there’s no harm in it. Where it goes wrong is replacing a cabinet front or a toe-kick panel: if the thickness is off, you’ll damage the surrounding run, and if you’re pulling a cabinet box that shares a water supply or an outlet, you’re now in plumbing and electrical territory. We recommend a trained installer for anything behind the doors. Most jobs are completed in a single visit. Call (888) 419-3650 to schedule your free estimate, and a live person answers, 24/7.
FAQs
Dvele cabinet systems are built to hold up for 15 to 20 years or more with normal use; in Antioch’s hot, dry summers and wet winters, panel and finish failures usually show up earlier than the boxes themselves. Call (888) 419-3650 for a free assessment – we’ll tell you what’s worth replacing and what isn’t.
Often yes. A single failed hinge, drawer slide, or door front can be repaired or swapped without touching the rest of the kitchen. Call (888) 419-3650 for a free estimate and we’ll quote the repair against a full replacement so you can decide.
Most Dvele part swaps and cabinet repairs are completed in a single visit, while a full cabinet run replacement typically takes one to three days. Call (888) 419-3650 to schedule your free estimate and get a timeline for your kitchen.
We match your part by model, series, and measured specs, then source either an original Dvele replacement or a quality equivalent in the same thickness and finish. Call (888) 419-3650 and we’ll tell you what’s available for your kitchen.
Written by the team at Groundwork Construction Co. of Antioch, serving Antioch and nearby areas.