Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation: The Antioch Owner’s Guide
Jerith aluminum ornamental fence installation in Antioch typically runs $3,500 to $9,000 installed, depending on linear footage, height, gate count, and whether we’re replacing panels on existing posts or setting new footings. We install Jerith-compatible systems across Antioch and quote most jobs in a single visit. Groundwork Construction Co. of Antioch is an independent installer, not affiliated with Jerith.
Owners usually find the problem the same way: a gate that drags on the concrete, a post that rocks when you lean on it, or a powder-coat finish that’s gone chalky and started flaking at the welds. In Antioch’s dry summers and clay-heavy soils, fence failures rarely announce themselves. They show up as a half-inch of sag after eleven years of heat cycling, or rust bleeding from a scratched rail after the third summer. We see it constantly on the older tracts off Lone Tree Way and in the hillside lots where drainage runs under the fence line.
Which Jerith Models This Applies To
Jerith builds ornamental aluminum in a handful of residential lines, and the parts don’t cross over cleanly. Their classic picket series uses square-section pickets and pressed spear finials, while the Imperial and Renaissance-style lines run larger rails and different post caps. The punched-rail systems take a specific bracket; the older rackable styles don’t. If you’re matching a single panel or replacing a gate, the rail profile and picket spacing (typically 3-7/8″ to 4″ on center for residential) have to match the existing run or the new section will look wrong from the street.
Identify your fence by measuring post spacing (usually 6′ or 8′ on center), rail height, and picket width before you order anything. Look for a stamp or sticker on the inside of a rail or the bottom of a post cap. If the label’s gone, photos and measurements get us there.
On the OEM-versus-aftermarket question: Jerith’s own parts guarantee a color and profile match, and their powder-coat warranty travels with the component. Quality aftermarket aluminum can work for a hidden rail or a post cap, but mixing coatings on a visible run is how you get a two-tone fence in three years. For anything facing the street in Antioch, we source the matching Jerith component when it’s available. We don’t stock parts and we don’t carry them on a truck; every part is ordered to your measurements.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Jerith Fence Installation Is Failing
- Posts that rock or lean. Usually a footing that was set too shallow for Antioch’s expansive clay, or a post that sat in water through a wet winter. If you can move it by hand, the concrete has failed.
- Rust at welds and scratch points. Powder coat is a barrier, not armor. A nick from a string trimmer opens bare aluminum or steel hardware underneath, and our dry-season dust plus winter rain finishes the job.
- Sagging gates that drag. Hinge wear plus a post that’s settled a quarter inch. Left alone, the gate racks and the latch stops lining up.
- Loose or missing pickets. Bracket corrosion or a punched-rail tab that’s fatigued. Common after a decade of thermal expansion in full sun.
- Chalky, faded finish. UV breakdown of the powder coat, faster on south- and west-facing runs. Once it chalks, recoating is a stopgap, not a fix.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Most Jerith-compatible fence installation in Antioch lands in the $3,500 to $9,000 range. The low end is a short run on existing, sound footings; the high end is a full run with new concrete footings, a walk gate, and a drive gate. Line-item pricing breaks down roughly like this:
- Panel and picket replacement on existing posts: $60 to $140 per linear foot installed
- New posts and footings: $150 to $300 per post, including concrete and set
- Walk gates: $400 to $900; drive gates: $900 to $2,200
- Full removal and haul-away of the old fence: $300 to $800
What drives the range is footage, gate count, footing depth (Antioch clay and slope change this), and whether we’re matching an existing finish or starting fresh. You get a written, line-item quote before we start; the number you approve is the number you pay. All installation work is covered by our 730-Day Done Right Promise, and the material carries the manufacturer’s finish warranty.
DIY or Call Us?
There’s a safe middle ground. You can check for post movement by hand, photograph the rail and picket profile, measure spacing, and confirm your model before ordering a part. That saves time and money.
Where DIY goes wrong on aluminum fence is the footing and the tension. Setting a post in Antioch clay without proper depth and drainage means it leans within two seasons. Racking a gate to fit without addressing the settled post just transfers the stress to the hinges. And a dropped or improperly anchored panel is a genuine hazard if it’s holding a gate line. If a post is moving, that’s the point to stop and call. We’ll tell you honestly whether it’s a part swap or a footing job.
Call (888) 419-3650 to schedule your free estimate. A live person answers around the clock.
FAQs
How long does a Jerith aluminum fence last in Antioch? A properly installed Jerith aluminum fence typically lasts 20 to 30 years in our climate, with the powder-coat finish being the first thing to go, often around the 10 to 15 year mark on sun-exposed runs. Call (888) 419-3650 for an exact quote on your run.
Can a failing section be repaired instead of replaced? Often, yes. If the posts and footings are sound, we can replace individual panels, pickets, or a gate without touching the rest of the run, which keeps cost down. We’ll tell you at the estimate whether repair makes sense or whether you’re throwing money at a footing problem.
How long does the swap take? A gate or small panel replacement is usually done in a single visit. A full run with new footings typically takes one to three days depending on footage and gate count. We confirm the timeline in writing before we start.
How do you source the part? We measure your existing profile, rail height, and picket spacing, then order the matching Jerith component to spec. We don’t stock parts or carry them on a truck, so lead time depends on the specific part, and we’ll tell you upfront what to expect.
We also work with KraftMaid, Cambria, and Silestone on other projects, but fencing is what we’re talking about here. Call (888) 419-3650 for a free estimate on your Antioch fence.
Written by the team at Groundwork Construction Co. of Antioch, serving Antioch and nearby areas.