Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Roofing: The Antioch Owner’s Guide
We install Unilock-compatible roofing components across Antioch, and the all-in price for a full Unilock roof system on a typical Antioch ranch or two-story home runs roughly $8,000 – $20,000 depending on pitch, square footage, and whether tear-off is needed. Individual component replacement (ridge, flashing, underlayment sections) is far less and often finished in a single visit. We don’t publish a one-size number because Unilock systems are modular – the panels, edging, and fastening hardware have to match your specific profile.
Owners usually find the problem the same way: a stained ceiling in a Delta-breeze-exposed bedroom, granules in the gutter after the first fall rain, or a soft spot near the ridge that never quite dried out. Antioch’s hot, dry summers and winter wind events put real stress on any roof system, and Unilock’s interlocking profiles show their age in specific, predictable places. That’s what we look for first.
Which Unilock Roofing Models This Applies To
Unilock makes more than one roofing profile, and part matching is where most owners get stuck. The three families we see most often on Antioch roofs are the standard interlocking shingle profile, the larger-format panel system, and the hybrid ridge-and-field assembly. Each uses a different fastening pattern, different edge trim, and – this is the compatibility gotcha – different clip geometry. A clip from the shingle profile simply will not seat on the panel system. Before you order anything, check the product stamp on the underside of an intact piece (usually near a gable edge or under a ridge cap) and measure the exposure width of a single course. That measurement tells us exactly which Unilock line you have.
On the OEM-versus-aftermarket question: Unilock’s own replacement parts are the safest match, especially on the interlocking profiles where tolerances are tight. Quality aftermarket equivalents exist for edging, fasteners, and underlayment and perform fine – but we don’t recommend third-party clips or ridge components on Unilock panels. The dimensional spec between the interlock and the clip is where cheap aftermarket parts fail in years, not decades. We source OE-compatible parts and can tell you honestly when a genuine Unilock part is the only thing that fits.
Groundwork Construction Co. of Antioch is an independent service provider and is not affiliated with Unilock.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Roofing Is Failing
These are the symptoms we find on Antioch roofs, and what’s actually going on underneath:
- Granule loss at the ridge and valleys. Wind and sun exposure break down the top layer first at the highest-stress spots – not a sign the whole roof is gone, but a sign the weathering surface is at end of life and the underlayment is next.
- Interlock separation along a course. Panels or shingles lifting at the seam mean the clips or fasteners have backed out, usually from thermal cycling. Left alone, water gets under the interlock and into the deck.
- Water staining on the ceiling below a ridge. A ridge cap or flashing failure shows up as a brown ring on drywall. This is a small repair if caught early and a deck replacement if you wait.
- Soft spots when you walk the roof. Deck rot under a Unilock panel means moisture has been trapped – often at a flashed penetration. This is why we probe every valley on an inspection.
- Visible edge trim lifting or curling. Unilock edge components lift when the fasteners corrode, and once the edge opens, wind-driven rain gets under the field. In Antioch’s wind corridors, this can go from cosmetic to structural in a single season.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included in an Antioch Unilock Roofing Job
Here’s what roofs actually cost in Antioch, with parts and labor broken down honestly:
| Job | Installed range |
|---|---|
| Roof repair (flashing, ridge, small section) | $400 – $1,800 |
| Tile roof repair (Unilock tile profile) | $600 – $2,500 |
| Full roof replacement (standard asphalt/Unilock-compatible) | $8,000 – $20,000 |
| Metal roof installation | $15,000 – $40,000 |
The range moves on three things: square footage, roof pitch (a 10/12 costs more to walk than a 4/12), and whether the old roof has to come off. OEM Unilock parts carry a small premium over aftermarket – usually 10 – 20% on the component line – and we show you that difference in the written quote, line by line. Every job we complete is covered by our 730-Day Done Right Promise. If the workmanship fails, we make it right.
DIY or Call Us?
Some of this an owner can safely check. Walk the ground and look at the roofline with binoculars for lifted edges or missing panels. Look in the attic after a rain for staining. Snap a photo of a product stamp. But roof work at height on a pitched Unilock system is where DIY goes wrong – falls are the leading cause of home-injury hospital visits in California, and a badly seated panel or mis-torqued fastener won’t leak on day one; it leaks on day 400. Replacing a single ridge cap or an edge trim is a reasonable homeowner repair on a low-pitch roof if you’re comfortable on a ladder. Anything involving the field, flashing, or a valley is a two-person job with fall protection. Call (888) 419-3650 and we’ll tell you honestly which side of that line your repair sits on.
FAQs
A properly installed Unilock roof system lasts 20 – 30 years here, with the lower end on asphalt-profile products in full sun and the upper end on tile and metal. Antioch’s dry heat and wind exposure are harder on the weathering surface than on the deck, so the fasteners and edge trim usually need attention before the panels do. If your roof is past 15 years and showing any of the symptoms above, call (888) 419-3650 for a free inspection.
Yes, in most cases. If the deck is sound and the failure is localized to flashing, ridge caps, edge trim, or one course of panels, a targeted repair costs $400 – $2,500 in Antioch and is usually done in a single visit. Full replacement only makes sense when the underlayment is shot or the deck has soft spots. We’ll tell you which you’re looking at before any work begins.
A ridge cap, edge trim, or flashing repair is typically a half-day to a single visit. A section of field panels or a valley redo runs one to two days depending on access and whether the deck needs repair. We schedule most Unilock repairs in Antioch within the week – call us to get a date on the calendar.
We match by product stamp and exposure measurement, not guesswork. Send us a photo of the stamp from an intact panel and we’ll identify the profile and order the OE-compatible part. We don’t carry parts on a truck – the right part is ordered and delivered to the job, which is why we don’t guess on specs. Call (888) 419-3650 to start the match.
Whether you have a Unilock roof that needs a single part or a full replacement, we’ll walk the roof, measure the exposure, and quote you a fixed price in writing. We also work with KraftMaid, Cambria, and Silestone on the interior side, and everything we install is backed by our 730-Day Done Right Promise. Call Groundwork Construction Co. of Antioch at (888) 419-3650 for a free estimate.
Written by the team at Groundwork Construction Co. of Antioch, serving Antioch and nearby areas.