Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Pittsburg, CA: What the Job Actually Involves
A tub-to-shower conversion in Pittsburg usually runs $3,500 – $10,000 and takes three to seven working days from demo to final inspection, depending on whether the drain has to move. The job means pulling the tub, reshaping the drain and waterproofing to a sloped shower floor, then setting a new pan, tile or surround, valve and glass. Most conversions here fit the $9,000 – $28,000 bathroom band when you fold in tile, fixtures and a permit. Call (888) 419-3650 for a free on-site estimate before you decide anything.

How we take a tub out and put a shower in: the five stages
We run every conversion in Pittsburg on the same sequence, because skipping a stage is how showers leak into the room below. You’ll know what’s happening on day one versus day four.
- Stage 1 – Site protection and shutoff (half a day). We mask the floor and hallway, kill the water, and pull the tub valve. You confirm the shower footprint and where the new valve goes, since the old tub valve sits about 18 inches off the floor and has to rise to 44 inches for a shower.
- Stage 2 – Demo and inspection (day one). The tub, surround and old backer come out, and we open the wall enough to see the drain and the framing. This is the moment we text you photos: what we find under a 1970s tub in Pittsburg often changes the plan, and you’ll approve any change before we keep going.
- Stage 3 – Rough plumbing and permit inspection (day two to three). If the drain stays put, the rough-in is quick. If you want a linear drain or a curbless entry, the slab or subfloor changes and the plumbing inspector signs off before anything is closed up. You choose the drain position here, not later.
- Stage 4 – Waterproofing and set (day three to five). We build the sloped pan, tape and coat the seams, and flood-test. Tile or a solid surround goes down over the cured membrane. You pick the waterproofing system and tile at the estimate, because changing it mid-set adds days.
- Stage 5 – Fixtures, glass and punch (day five to seven). Trim, valve cartridge, showerhead, glass panel and door go in, then we test the drain and hand you the written walkthrough. Final inspection closes the permit.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between, and what each really costs you
The conversion isn’t one product. It’s four or five decisions, and each swings the price and the lifespan. Here’s the honest trade-off on each.
- Shower pan: mud-set tile vs. a prefab base. A tiled mud pan runs $1,200 – $2,800 installed and lasts decades if it’s built right. A prefab acrylic base like a Sterling unit costs $400 – $1,100 and installs in a day, but a 30-inch base limits how the room feels. If you want curbless, it’s mud or a foam tray system every time.
- Wall finish: ceramic tile vs. large-format porcelain vs. a solid surround. Standard ceramic is the budget pick; large-format porcelain (12×24 or bigger) looks sharp but demands a flat, prepared substrate and a tiler who knows it. A solid acrylic surround is the fastest and easiest to clean, and the best fit for a rental or an aging-in-place bathroom.
- Waterproofing: liquid membrane vs. a bonded sheet system. We use a bonded sheet system like Schluter on most conversions because the seams are factory-made and the flood test is fast. A liquid membrane is cheaper and fine in a small shower, but it needs more cure time between coats.
- Valve and trim: a basic pressure-balance valve vs. a thermostatic setup. A Grohe or Toto thermostatic valve costs more upfront and gives you precise temperature control, which matters in a Delta-windy house where supply temps shift. A standard pressure-balance valve is the budget standard and satisfies code.
- Glass: framed panels vs. frameless. Frameless glass runs $900 – $2,200 and makes a 36-inch shower feel larger. A framed enclosure is $350 – $800 and more forgiving in a room with an out-of-square frame, which older Pittsburg baths often have.
What Tub-to-Shower Conversion costs in Pittsburg, CA
Here’s the line-item picture for this job specifically. A full bathroom remodel sits in the $9,000 – $28,000 band; a conversion alone is narrower.
| Item | Typical range |
|---|---|
| Tub removal and demo | $400 – $900 |
| Drain relocation or re-rough (if needed) | $600 – $2,000 |
| Sloped pan, waterproofing and bonding flange | $1,200 – $2,800 |
| Tile or surround, walls and floor | $1,000 – $3,500 |
| Valve, trim set and showerhead | $400 – $1,400 |
| Glass panel or door | $350 – $2,200 |
| Permit and inspections | $250 – $800 |
Five things push the number up or down:
- Drain position. Keeping the tub drain in place is the single biggest cost saver. Moving it to the center of a wider shower means opening the floor.
- Existing condition. A wet wall with rot behind the tile, common in riverfront and downtown homes near the old mill, adds demo and framing.
- Structure and layout. Turning a 30-inch tub alcove into a 48-inch shower means cutting a wall, and your contractor has to know whether it’s load-bearing first.
- Material grade. Standard ceramic lands near the low end of the $3,500 – $10,000 range. Large-format porcelain, frameless glass and a thermostatic valve push you toward $10,000.
- Permit scope. A straight swap with a new valve is a simpler inspection than a relocation with new plumbing and electrical.
Our written estimate lists every line and moves only if you approve a change in writing, which is what we mean by upfront pricing, no surprises. Estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat Pittsburg homes specifically do to this job
Pittsburg’s housing stock splits the conversion into two very different working conditions, and our technicians have up to 12 years of experience on both. Downtown and riverfront homes near the old steel mill and canneries are early-1900s and post-war builds, sitting on Delta fill and clay that has settled over time, so walls are rarely square and floors run a little out. In those houses the tub alcove is often framed in old dimensional lumber, and we inspect the wet wall and the subfloor before we promise a fixed price. Up on the Ridge and the hillside subdivisions, the builder cut a pad into expansive clay, so you’ll find a slab that has shifted a few degrees since the last owner remodeled, which affects how a glass panel sits and how a curbless entry has to be shimmed.
The Delta breeze that funnels through the Carquinez Strait gap is the other factor. It pushes driven moisture against exterior walls, so we pay close attention to the waterproofing detail and ventilation on any conversion on the windy side of the house. If your broader plan touches the roof or the exterior, homeowners often pair a conversion with Metal Roofing in Pittsburg or Tile Roofing in Pittsburg while the crew is already on site, and we’ll quote the whole scope on one estimate.

Permitting runs through standard Contra Costa County code requirements for plumbing and wet-area waterproofing, and we pull the permit and schedule both the rough plumbing inspection and the final. We handle it as part of the Bathroom Remodeling in Pittsburg scope for our Pittsburg customers, so you’re not chasing paperwork. If the conversion is one piece of a larger Bathroom Remodeling plan, we fold it into a single project calendar.
Serving Pittsburg, CA – Our Local Coverage Area
We serve Pittsburg and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: Tub-to-Shower Conversion in Pittsburg
Most conversions take three to seven working days from demo to final inspection. A straight swap with the existing drain in place runs closer to three; moving the drain or going curbless puts you near seven, and permit review time is separate.
Yes, when the plumbing or waterproofing changes, you need a permit with a rough and final inspection. We pull it for you and schedule both inspections, so you’re not the one waiting on the county.
Yes, in most cases. If the shower keeps roughly the tub’s footprint and the existing drain is sound, we build the new pan over the old drain location and skip the floor opening and most of the added cost.
Plan on $3,500 – $10,000 for the conversion itself, or $9,000 – $28,000 as part of a full bath update. The drain position, tile grade and glass type move the number most. Call (888) 419-3650 for an exact quote, and estimates are free.
Every conversion is covered by our 730-Day Done Right Promise: if something isn’t done right, we make it right. That covers the waterproofing and finish work, and we put it in writing with the estimate.
Get a free estimate for your Pittsburg conversion
We’ll come to your home, measure the tub alcove, check the drain and wet wall, and hand you a line-item estimate for your Tub-to-Shower Conversion in Pittsburg. Calls are answered by a live person 24/7, and projects over $10,000 qualify for $1,000 off plus 0% financing for 18 months. Call (888) 419-3650 to schedule your free estimate and design consult.
Written by the team at Groundwork Construction Co.