Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Brentwood, CA: What It Takes and What It Costs
Door installation in Brentwood typically runs $450 to $2,800 per door, includes removal of the old unit, framing adjustments, flashing and weather seal, and takes one to two days for a single exterior door. Interior doors land at the low end, entry and patio systems at the high end. Call (888) 419-3650 for a free on-site estimate. The number we quote in writing is the number you pay.

How Our Door Installation Process Runs, Stage by Stage
Every door job follows the same sequence, and the same rule: you approve each decision before the next stage begins. Here’s what actually happens.
Stage 1 – Measurement and on-site assessment (45 to 90 minutes). We check the rough opening, wall thickness, header height and whether the existing door sits plumb. In Brentwood’s stucco-walled homes this matters more than in most places: wind-driven dust and seasonal clay movement can throw a jamb out of square by a quarter inch or more over a couple of decades, and that shows up before we cut anything. You decide the door style, material and swing direction at the end of this visit.
Stage 2 – Order and confirmation (one to three weeks, depending on lead times). Standard sizes ship faster; custom widths, sidelites and non-standard hardware take longer. You confirm the final spec sheet and the cost breakdown in writing. No change orders without your sign-off.
Stage 3 – Prep and removal (two to four hours). We protect the floor and adjacent trim, pull the old door and frame, and expose the rough opening. On older doors this is also when we see what the old unit was hiding: rotted sill plates, water staining at the threshold, and on some Brentwood homes, framing that was never fully flashed. We photograph what we find and tell you the cost of the fix before we proceed.
Stage 4 – Installation and sealing (four to six hours). New door, hinges, lockset, weather-stripping and threshold go in. Exterior doors get flashing tape, backer rod and a paintable sealant joint – critical in a climate that swings from cold Delta mornings to 100°F afternoons. We set the hinge side first, then shim and adjust so the door closes with one hand and latches smoothly.
Stage 5 – Inspection and final walkthrough (30 to 60 minutes). We check square, latch alignment, gap sealing and finish, then walk you through the operation. Any stucco or interior trim patching is scheduled separately so the sealant and paint can cure.
One honest note on the job: a door is a compression and structural opening. Moving a door in a load-bearing wall, or resizing an opening to fit a wider unit, means framing changes, a permit and a licensed structural assessment. We handle that as part of a Windows & Doors in Brentwood scope if you’re doing several openings at once, but we won’t talk you into it when a simple replacement meets your needs.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Door Options You’ll Actually Choose Between
For most Brentwood homeowners the decisions come down to four things: material, configuration, hardware and finish. Here’s the honest trade-off on each.
- Fiberglass entry doors – $800 to $2,200 installed. Hold up well to sun and temperature cycles, available in wood-grain embossing, won’t warp or split. The right call for most exterior doors here.
- Solid wood doors – $1,200 to $3,000 installed. Beautiful, but they need re-sealing every few years against UV and dry heat. Suits shaded entries better than south-facing ones.
- Steel doors – $600 to $1,500 installed. Strong, secure, budget-friendly; dents and rust at the bottom edge if the finish isn’t maintained.
- Interior doors (hollow or solid core) – $450 to $1,400 installed per door. Hollow-core is cheap and light; solid-core cuts sound transmission and feels substantial in bedrooms and bathrooms.
- Configuration – Single door, door with sidelites, double French, or a slider. Each adds framing complexity. Sidelites add roughly $300 to $900 in labor and materials.
- Hardware and finish – $80 to $500 depending on the handle set, deadbolt, and whether you want smart-lock compatibility. Standard finishes hold up better than specialty ones in this climate.
- Energy performance – If you’re matching an energy-efficient window package, choose a door with a certified core or glazing. Andersen and Marvin entry systems are common pairings with the window work we do here.
What Door Installation Costs in Brentwood, CA
Expect $450 to $2,800 per door installed, with most single-entry jobs landing around $1,100 to $1,600. Here’s what moves a job toward the low or high end:
- Door type and size: standard 36-inch interior doors sit at the bottom; oversize or custom entry units at the top.
- Existing condition: a clean opening is straightforward; rot, out-of-square framing or missing flashing adds $150 to $600 in repair labor.
- Configuration: sidelites, transoms and double doors add framing, hardware and trim complexity.
- Material grade: a quality fiberglass or steel door saves money up front; solid wood costs more and requires more maintenance.
- Permit scope: like-for-like replacement usually doesn’t require a permit in Brentwood; resizing an opening or altering a load-bearing wall does, and that adds inspection time and cost.
A written estimate from us itemizes the door unit, labor, hardware, flashing and sealant, trim, disposal, and any repair or permit work. What isn’t included unless we spell it out: painting or staining after installation, interior drywall patching beyond the door casing, and stucco repair beyond the immediate opening. If you want the wider scope covered at the same time, look at our Windows & Doors service.

See the difference
Before
After
Before
After
Before
AfterWhat Brentwood Homes Specifically Do to Door Installation
Brentwood’s housing stock is overwhelmingly new: large tracts of 1990s through 2020s stucco homes, plus custom ranchettes on multi-acre lots and a small core of older downtown bungalows. That mix shapes door work here. In the newer tracts, the most common issue is builder-grade hollow-core interior doors that have swelled or delaminated after a couple of decades of hot, dry summers. In the older bungalows, we regularly find entry doors that were never properly flashed, showing rot at the threshold from seasonal watering and Delta winds.
One local wrinkle worth knowing: on former orchard land, the same expansive clay soil that shifts foundations also shifts door frames. We see doors that close in winter and stick in July, and we address the symptom honestly before we replace anything. Brentwood’s hot, dry climate also means finish quality matters more than most homeowners expect; an unsealed door facing west will need re-sealing in three years, not ten.
On the permit side, Brentwood’s grading and drainage requirements are stricter than many older Bay Area cities, and HOA design review for exterior door color or style is common in the newer developments. We’ll tell you what your specific development requires before you order. We cover Brentwood and the surrounding area – see our Brentwood service page for the full picture.
Serving Brentwood, CA – Our Local Coverage Area
We serve Brentwood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Door Installation in Brentwood
A single interior door takes about two to three hours; a standard exterior entry door takes four to six hours; and a full entry with sidelites or a patio door can take a full day. Lead time for the door itself is usually one to three weeks depending on the spec. Call (888) 419-3650 to schedule a free estimate and get a firm timeline.
Like-for-like replacement usually doesn’t require a permit. Resizing an opening, moving a door, or altering a load-bearing wall does – and that work needs plans and inspection. Our team walks you through the permit question at the estimate so there are no surprises. Call (888) 419-3650 for the specifics on your job.
Yes, in most cases. If we’re swapping a door into the existing opening, no plumbing or framing moves. If the layout needs a new opening, that changes, and we’ll say so upfront. Call (888) 419-3650 for a free assessment.
Most jobs land between $450 and $2,800 per door, with standard entry work around $1,100 to $1,600. Door type, existing condition, configuration and permit scope drive the number. Call (888) 419-3650 for a written estimate – it’s free.
Every door we install is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. If something isn’t right, we make it right. Call (888) 419-3650 with questions about coverage.
Homeowners replacing doors often pair the project with exterior work while the walls are open – a Chain Link Fence in Brentwood or a Vinyl Fence in Brentwood to finish the yard at the same time.
Get a Free Door Installation Estimate in Brentwood
Call (888) 419-3650 and you’ll reach a live person, day or night. We’ll schedule a free on-site estimate, measure the opening, walk you through the door options that fit your home, and hand you a written line-item quote with upfront pricing and no surprises. Projects over $10,000 get $1,000 off, and 0% financing for 18 months is available. Estimates are free.
Written by the team at Groundwork Construction Co.