Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Asphalt Driveways & Resurfacing in Concord: What You’re Actually In For
Asphalt driveways & resurfacing in Concord covers two related jobs: laying a brand-new asphalt drive (typically $3,500 – $9,000) and resurfacing an existing one that’s cracked or worn (usually a fraction of that, and often booked as a stand-alone visit). Figure one to three days on site for a new pour, depending on size and access. Call (888) 419-3650 for a free on-site estimate and a written line-item quote before anything gets torn out.

Stage by Stage: How an Asphalt Driveway Comes Together
Asphalt isn’t poured like concrete, and that trips people up. It’s mixed hot, laid in lifts, and compacted with a roller. The quality of the job lives almost entirely in the prep work you’ll never see again once the blacktop goes down. Here’s the sequence we follow, stage by stage, so you know exactly what’s happening on day one versus day three.
Stage 1 – Site walk and layout (day 1, 1 – 2 hours)
We measure the drive, check slope and drainage, and locate utility lines before a single shovel hits the ground. This is where you decide on width (a standard single-car drive runs 10 – 12 feet; a double runs 16 – 20) and confirm the finished grade so water runs away from the house, not toward the slab. On older Concord lots with an unexpected septic or irrigation line, this is the moment we find it – not after excavation.
Stage 2 – Excavation and subgrade prep (day 1, 3 – 6 hours)
We strip the old surface and dig down to a stable base, typically 6 – 10 inches depending on soil and expected load. Concord’s valley-floor soils can carry a fair amount of clay, so we watch for pockets that hold water and correct them before anything is built back up. If your existing drive has failed in one section but held elsewhere, the subgrade is almost always the reason.
Stage 3 – Base rock and compaction (day 1 into day 2)
Crushed aggregate goes down in layers, each one watered and rolled until it’s tight. This base is what carries the weight of your vehicles; the asphalt itself is really just the wearing surface. Skipping layers or rolling short is the single most common shortcut, and it’s the one that shows up as cracking two summers later.
Stage 4 – Hot-mix asphalt placement (day 2, 2 – 4 hours)
The hot mix arrives, gets spread to grade, and is rolled while it’s still workable. For a standard residential drive we lay 2 to 3 inches of compacted asphalt over the base. Edges get tapered or set against a border. This is the stage where the temperature of the mix and the timing of the roller matter; it’s not a job you can pause halfway through.
Stage 5 – Cure and return to service (day 2 into day 3)
New asphalt needs to cool and set. You can usually walk on it the same day and park on it after 24 to 48 hours, with heavier loads waiting a bit longer in hot weather. A fresh seal coat, when included, goes on weeks later once the asphalt has cured. Resurfacing jobs skip the excavation stages and move faster, often finishing in a single day.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Weave Through Before We Start
Most of the real decisions happen before day one, and each one shifts both the price and how the drive holds up over the next decade. Here’s what actually gets chosen between.
- New asphalt vs. resurfacing an existing drive. Resurfacing (an overlay or a mill-and-replace) is cheaper and faster when the base is still sound. If the subgrade has failed, an overlay just hides the problem for a season or two. We’ll tell you honestly which one your drive needs.
- Asphalt thickness. A standard 2 – 3 inch compacted lift suits most residential drives. Heavier use, a steep grade, or a spot where an RV parks calls for more. Thickness is one of the biggest cost levers, and going thin to save money is a false economy.
- Edge treatment. A plain tapered edge is the budget option. A concrete or paver border holds the asphalt edge in place and looks sharper; Belgard makes border units that pair cleanly with a neighboring walk. Border work adds cost and is worth it on drives that see a lot of turning.
- Seal coat timing and frequency. A fresh drive should cure for several months before its first seal. After that, sealing every two to three years keeps sun and water from eating the binder. Skipping it shortens the drive’s life; over-sealing traps moisture.
- Drainage integration. Channel drains, French drains, or a simple crowned grade all push water off the drive. On a lot where the drive slopes toward the garage, this is the difference between a dry slab and a recurring problem.
- Apron and approach transitions. Where the drive meets the street or a sidewalk, the transition detail has to match the city’s requirements and hold up to turning tires. This is often where cheap jobs show their seams first.
If the drive is part of a full Driveway & Pavers in Concord project that includes walks, a patio, or a front-entry redesign, we plan the whole thing together so the grades line up and one trade doesn’t undo another’s work.
What Asphalt Driveways & Resurfacing Costs in Concord, CA
For Concord, a new asphalt driveway generally runs $3,500 – $9,000, and resurfacing an existing drive typically lands lower depending on how much prep it needs. A full driveway replacement, where the old surface comes out and a new one goes in, sits around $5,000 – $14,000. Sealing, on its own, is a much smaller line item when it’s done as maintenance.
Here’s what moves a quote toward the low or high end:

- Square footage and shape. A straight single-car drive is the simplest job. Curves, a turnaround, or a long run to a detached garage all add material and labor.
- Existing condition. A failed base means excavation; a sound base means an overlay. That single call can change the number by thousands.
- Site access. If a truck and roller can’t easily reach the work area, everything slows down and the price reflects it.
- Drainage work. Adding drains or correcting a grade that currently sends water at the house adds cost that isn’t in a basic paving quote.
- Permits and street-front work. Anything touching the public right-of-way at the apron may need a permit and inspection.
Your written estimate spells out the square footage, the asphalt thickness, the base depth, edge treatment, and whether drainage or a permit is included. It doesn’t include things you haven’t asked for – like relocating a utility line, cutting out a damaged apron, or a full border install – unless we’ve discussed them and put them in writing. Upfront pricing, no surprises: the number you see is the number you pay, backed by the 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Concord Homes Specifically Do to This Job
Concord’s housing stock shapes asphalt work in ways a generic paving crew won’t anticipate. Much of the city is post-WWII and 1950s – 70s single-story ranch tract homes, and plenty of those drives were laid decades ago over shallow bases that have since settled. The area’s mid-century buildout also means original slab foundations and aging utility runs that sit close to the surface – so excavating a drive in a tract off Clayton Road or near the downtown BART corridor often turns up irrigation lines, old footings, or unpermitted additions from an earlier era that we need to work around, not through.
The climate does its part too. Concord sits where the cool, fog-influenced Diablo Valley floor meets the hot Mount Diablo slopes, so the same neighborhood can have shaded, moisture-heavy drives on one side and sun-baked, heat-cracked asphalt uphill. Hot, dry summers push thermal expansion on a black surface; wet winters stress whatever drainage the drive was built with. Newer master-planned pockets tend to have cleaner, flatter drives; older tracts toward the foothills throw grade and drainage curveballs. We look at the specific lot, not a template. Homeowners often pair drive resurfacing with a New Detached ADU in Concord when adding parking for a second household, or with a Junior ADU & Interior Conversion in Concord when the drive access needs rethinking.
We handle asphalt driveways & resurfacing across Concord – ZIP codes 94519, 94522, 94524, and 94529 included – and we’ll pull any required permits and see them through inspection where the work touches the public right-of-way. If your drive is one piece of a larger exterior plan, our Driveway & Pavers service covers the rest of the hardscape, and you can see the full breadth of what we do on the Concord service-area page.
Serving Concord, CA – Our Local Coverage Area
We serve Concord and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Asphalt Driveways & Resurfacing in Concord
A new asphalt driveway usually takes one to three days on site, plus a short cure before you park on it. Resurfacing is often a single day. Planning and permit approval, when needed, add time up front. Call (888) 419-3650 and we’ll give you a realistic timeline for your specific drive.
You need a permit when the work touches the public right-of-way or the street apron; a drive entirely on your own property often doesn’t. Requirements vary by how close you are to the street, sidewalk, or a drainage easement. We look at your lot and tell you what applies before work begins – that’s part of the free estimate, so call (888) 419-3650.
Yes, when the base underneath is still sound. Resurfacing lays new asphalt over a prepared existing surface and skips full excavation. If the base has failed, an overlay won’t last and we’ll say so. Call (888) 419-3650 for an honest assessment of which route your drive needs.
Resurfacing typically costs less than a new install, and a new asphalt driveway in Concord runs $3,500 – $9,000 while a full replacement sits around $5,000 – $14,000. What lands in that range depends on size, base condition, access, and drainage. Call (888) 419-3650 for an exact quote – estimates are free.
Not on our jobs. We put the scope in writing up front and stick to it – no change orders for work we already quoted. If we uncover something genuinely unexpected under the old surface, we stop and talk to you before proceeding. Your quote is backed by the 730-Day Done Right Promise. Call (888) 419-3650 to get started.
Get Your Free Asphalt Driveway Estimate in Concord
Call (888) 419-3650 to schedule a free on-site estimate for asphalt driveways & resurfacing in Concord. A live person answers, around the clock. We’ll walk your drive, check the base and drainage, and hand you a written line-item quote with the asphalt thickness, base depth, and permit scope spelled out. No pressure to book on the spot – just a real number from someone who’s prepared to stand behind it.
Written by the team at Groundwork Construction Co.