Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Walk-In Showers & Shower Remodeling in Walnut Creek, CA: What It Involves and What It Costs
Walk-in showers & shower remodeling in Walnut Creek usually runs $9,000 – $28,000 for a full rebuild, or $4,500 – $12,000 when you’re replacing just the shower itself. Plan on two to four weeks of on-site work. Most of that time isn’t tile, it’s the waterproofing, plumbing rough-in, and inspection steps that decide whether the shower holds up for twenty years or leaks into your subfloor in three. Call (888) 419-3650 to schedule a free on-site estimate.

Our Shower Remodeling Process, Stage by Stage
Here’s exactly how a walk-in shower project moves from first hammer swing to final caulk line, and where you’ll need to make a decision.
Stage 1: Site protection and demolition (1 – 2 days)
We lay floor protection, seal off the rest of the bathroom, and shut the water at the fixture stops. Then the old shower pan, tile, backer, and any framed curb come out. You’ll decide here whether the existing drain location stays put. If it moves, that’s a plumbing change and it gets a permit amendment before we go further.
Stage 2: Framing, plumbing, and electrical rough-in (2 – 3 days)
This is where the shower is actually built. We check the stud bay for rot (common behind 1970s tile), reset the valve to the new depth, add a niche, and rough in any lighting or exhaust work. If the original ranch wiring in the wall is aluminum or ungrounded, this is when you find out. You’ll decide on valve trim and niche placement now, because once the board goes up the layout is locked.
Stage 3: Inspection (0 – 3 days, scheduled)
A permitted shower gets inspected after rough-in and before the waterproofing membrane goes on. We schedule that window in advance so it doesn’t stall the job. This is the step most homeowners don’t know exists, and it’s the one that protects resale.
Stage 4: Waterproofing and tile (4 – 6 days)
We install a bonded waterproofing system, then set tile with 95%+ coverage on the walls and a properly sloped pan. Curing time between waterproofing and tile matters, so we don’t rush it. You’ll confirm grout color and layout here; layout on a large-format tile is where small changes get expensive.
Stage 5: Glass, trim, and final walkthrough (1 – 2 days)
The enclosure, drain cover, fixtures, and caulk go in last. We run the shower, check slope and drainage, and walk the job with you. Everything here is covered by our 730-Day Done Right Promise, backed in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
- Tile vs. solid-surface walls. Porcelain or ceramic tile is the classic look and holds up well, but it’s labor-heavy and grout lines need attention. Acrylic and solid-surface panels cost less installed and clean easily, but they read more builder-grade and don’t add much resale value.
- Linear vs. center drain. A linear drain lets you use a single large-format tile on the floor with fewer cut joints, which looks sharper and drains faster. It costs more to plumb and install. A center drain is cheaper and simpler.
- Curbless vs. low-curb entry. True curbless (zero-threshold) entry means recessing the floor joists or building up the surrounding floor level. That’s structural work and it moves the price up. A low 2 – 3 inch curb gives you most of the walk-in feel without the framing change.
- Glass enclosure. Frameless 3/8-inch glass looks cleanest and lasts longest. Semi-frameless and framed units are cheaper but show their age faster at the metal.
- Fixtures and finish grade. Specifying a Grohe or Toto valve and trim set is a modest upcharge that pays back in fewer cartridge replacements. Off-brand valve internals are the most common failure point we see at the five-year mark.
What Walk-In Showers & Shower Remodeling Costs in Walnut Creek, CA
For Walnut Creek, a full shower remodel lands between $9,000 and $28,000. A shower replacement inside an existing footprint runs $3,000 – $8,500. Here’s the line-item picture on a permitted rebuild:

| Scope item | Typical range |
|---|---|
| Demo and disposal | $600 – $1,400 |
| Plumbing rough-in and valve | $1,200 – $3,800 |
| Waterproofing system | $900 – $2,200 |
| Tile and setting materials | $1,800 – $6,500 |
| Glass enclosure | $1,200 – $3,500 |
| Permit and inspection | $300 – $900 |
Five things push a job toward the top of that range: size (a 4×5 shower is not an 8-foot walk-in), condition behind the tile (rot or failed valve seals add framing and repair), moving plumbing or electrical, material grade (large-format stone-look porcelain costs far more than 4-inch ceramic), and how much structural work is needed for a true curbless entry. A written estimate from us lists each of these line by line, so the number you see is the number you pay. No change orders unless you ask for one.
See the difference
Before
After
Before
After
Before
AfterWhat Walnut Creek Homes Specifically Do to This Job
Most of the shower remodels we do in Walnut Creek happen inside 1950s – 70s single-story ranches and split-levels, and those walls tell you a lot the moment demo opens them up. Original ranch construction here often means minimal insulation and aluminum branch wiring, so pulling a shower down frequently triggers an electrical and insulation upgrade to meet current Title 24 energy standards. Plan for that possibility in your budget, especially on the 94596 and 94598 side where the postwar tract homes cluster. The other thing that shapes this job in Walnut Creek is the permitting climate: the city’s design review and hillside preservation rules mean even a bathroom scope gets scrutinized on structural and plumbing changes, so we pull the permits and schedule the inspection before any waterproofing goes on. That’s slower than working unpermitted, and it’s the reason a Walnut Creek shower that’s permitted holds its value at resale. The failure mode we see most: 1970s pans set without a proper pre-slope, which produces slow hidden leaks into the subfloor over a decade. That’s why a rebuild that includes a correct waterproofing system costs more than a tile-over, and lasts far longer.
Serving Walnut Creek, CA – Our Local Coverage Area
We serve Walnut Creek and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Walk-In Showers & Shower Remodeling in Walnut Creek
Plan on two to four weeks of on-site work for a permitted full remodel. The variable is the inspection window and the curing time between waterproofing and tile; the tile itself is usually the fastest stage. Call (888) 419-3650 for a schedule specific to your project.
Yes if plumbing, electrical, or structure changes. A pure finish replacement inside the existing footprint often doesn’t require one, but a curbless conversion or a moved drain does. We pull the permit and pass the inspection; you don’t have to touch the paperwork.
Usually, yes. If the drain and valve stay where they are, a low-curb walk-in fits in the same opening and the job is simpler and cheaper. A true zero-threshold shower is where structural work becomes necessary.
$9,000 – $28,000 for a full remodel, or $4,500 – $12,000 for the shower install alone. The range depends on size, condition behind the tile, plumbing changes, and finish grade. Call (888) 419-3650 for an exact quote; estimates are free.
Every shower we build is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. If it’s not done right, we make it right, and it’s in writing.
Get a Free Estimate for Walk-In Showers & Shower Remodeling in Walnut Creek
Call (888) 419-3650 to schedule a free on-site estimate. We’ll measure the space, open the walls enough to see what’s actually behind the tile, and give you a line-item price in writing, including permit costs and the exact fixture brands. Most Walnut Creek shower projects start two to four weeks after the estimate is signed. If your project is part of a full Bathroom Remodeling in Walnut Creek, we’ll sequence it with the rest. For the broader scope, see our Bathroom Remodeling service. We cover all of Walnut Creek and nearby Pleasant Hill, Alamo, Concord, and Clayton. Homeowners sometimes pair this with roof work; see Roof Replacement & Installation in Walnut Creek and Metal Roofing in Walnut Creek.
Written by the team at Groundwork Construction Co.