Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Danville, CA: What It Costs and How Long It Takes
Metal roofing in Danville runs $15,000 – $40,000 for a full installation, and most homes take six to twelve working days from tear-off to final inspection. The wide range comes down to roof size, pitch, how much old material has to come off, and whether you choose a standing-seam panel or a stone-coated steel profile. On a typical 94526 ranch home, a straightforward panel job lands closer to the low end; hillside homes in 94506 with steep pitch and complex hips push toward the top. Call (888) 419-3650 for a free estimate.

How a Metal Roofing Job Actually Runs, Stage by Stage
Metal isn’t a one-day install, and knowing the sequence helps you plan around it. Here’s what a real Danville metal roofing project looks like from start to finish.
- Stage 1 – Tear-off and deck inspection (1 – 2 days). We strip the existing shingles or tile down to the sheathing and check every board for rot, sag, or old water damage. On 1960s – 1980s Danville homes, we regularly find soft sheathing near valleys and chimneys that has to be replaced before anything goes on top. You’ll see photos of anything we flag before work continues.
- Stage 2 – Deck repair and underlayment (1 – 2 days). We replace bad sheathing, then lay a high-temp synthetic underlayment rated for metal. On homes in the western hillsides where fire exposure matters, we install a fire-rated underlayment to match the metal assembly. This is your decision point on upgrade options – ice-and-water shield at valleys and eaves, a peel-and-stick layer on steep southern pitches.
- Stage 3 – Trim, flashing, and panel layout (1 – 2 days). Fascia gets replaced or capped, then we run panel layout and set the eave and gable trim. How panels are oriented and where seams land is decided here. Get this wrong and you get leaks at penetrations.
- Stage 4 – Panel install (2 – 4 days). Panels go on and get screwed down with the correct gasketed fasteners for standing seam or stone-coated steel. Standing seam is concealed-fastener and takes longer than exposed-fastener profiles. Vents, skylights, and chimney flashings are all cut and sealed during this stage.
- Stage 5 – Ridge, cleanup, and inspection (1 day). Ridge caps go on, we magnet-sweep the entire yard for screws and metal shavings, and the job gets final inspection. Most metal roofing jobs in Danville complete in six to twelve working days; more complex rooflines with dormers and multi-hips take longer.
You’ll make decisions at three points: material profile on day one, underlayment upgrades on day one or two, and flashing/venting approach once we see the deck. Everything else runs on the crew calendar.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
What You’re Choosing Between in Metal Roofing
Metal isn’t one product. In Danville, the panel choice drives both the price and how the roof performs against a hot Tri-Valley summer. Here’s what actually matters.
- Standing seam panels. Concealed fasteners, cleaner lines, best long-term against wind and rain. Higher cost and steeper install labor; suits homeowners who plan to stay put and want the longest service life.
- Stone-coated steel. Looks like tile or shake but weighs far less – a real advantage for older Danville roofs that weren’t framed for heavy tile. Priced a bit under standing seam, more forgiving on complex rooflines.
- Exposed-fastener corrugated or ribbed panels. The most economical option. Faster install, but the exposed washers dry out and become leak points in intense UV. Suits outbuildings and simpler roof planes more than a primary residence.
- Color and finish. Cool-rated reflective coatings reduce attic heat – worth specifying in this climate. Rich dark colors look sharp but absorb more sun; lighter profiles hold up better under Danville’s summer sun.
- Panel gauge. 24-gauge stands up better to hail and foot traffic than thinner 26-gauge. The thin panels save on the front end and cost more in dents later.
What Metal Roofing Costs in Danville, CA
A full metal roof installation in Danville runs $15,000 – $40,000. Repair-level work on a small section is far less, and a straightforward tear-off-and-replace on a simple gable roof sits in the $15,000 – $22,000 band. Here’s what pushes a job toward the top of the range.
- Roof size and pitch. Square footage is the biggest lever. Steep pitches slow the crew and require additional fall protection.
- Existing condition. Rotten sheathing, multiple old layers, or a second layer to strip all add tear-off and deck repair cost.
- Roofline complexity. Dormers, multi-hips, valleys, and skylights each add flashing work. The ornate Mediterranean roofs common in Blackhawk homes run higher than a clean ranch roofline.
- Material choice. Standing seam and stone-coated steel sit at the top; exposed-fastener panels at the bottom. Color and gauge matter too.
- Permit scope. Structural upgrades, fire-rated assemblies required in the WUI, or correcting poor original framing all extend the permit and inspection timeline.
A written estimate from us includes tear-off, disposal, deck repair up to a stated allowance, underlayment, panels, trim, flashing, and final inspection – line-itemed so you see each number. It excludes structural framing replacement beyond the stated allowance and any work discovered only after tear-off. Nothing gets added without your written approval. Financing at 0% for 18 months and $1,000 off projects over $10,000 apply here.
See the difference
Before
After
Before
After
Before
AfterWhat Danville Homes Specifically Do to a Metal Roofing Job
Danville is a built-out, high-value Tri-Valley suburb, and almost every metal roof here replaces one that’s already 30 to 50 years old on a 1960s – 1990s custom or semi-custom home. That changes the job. The original deck wasn’t built for a heavy tile replacement, so stone-coated steel that mimics the original Mediterranean look often works better than a true tile swap. In the hillside 94506 zones near Blackhawk and Tassajara, WUI fire requirements mean the metal assembly, underlayment, and venting all need to meet fire-hardened standards, and access for delivery trucks and staging matters more than it does on a flat lot. The 94526 core has its own reality: mature landscaping, tight side yards, and roofs that show their age at valleys and chimneys rather than out in the open. Permits go through the Town of Danville, and most metal re-roofs require a permit and final inspection.

Owners remodeling $1.5M-plus homes they intend to keep tend to approach this as a long-horizon decision. If the wider scope includes gutters, fascia, or attic ventilation, that’s usually part of a full Roofing in Danville plan – and when owners are also upgrading exterior envelopes, they often pair metal roofing with Window Replacement in Danville or Impact Windows & Doors in Danville. We handle metal roofing throughout Danville and the surrounding Tri-Valley, and it sits alongside our full Roofing service.
Serving Danville, CA – Our Local Coverage Area
We serve Danville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Danville
Most Danville metal roofing projects take six to twelve working days from tear-off to final inspection. Simple gable roofs on a ranch home run shorter; steep or multi-hip rooflines on Blackhawk-area homes take longer. Permit turnaround from the Town of Danville adds a separate window before work starts. Call (888) 419-3650 to get an exact timeline for your roof.
Yes. A full metal re-roof in Danville requires a permit and final inspection, and the permit scope determines whether fire-rated assemblies or structural work get added. We pull and manage the permit as part of the job – you don’t chase it down. Call (888) 419-3650 for a free estimate that spells out the permit scope.
In most cases yes. If your existing framing is sound, metal roofing goes on the same deck after tear-off and underlayment. Lighter profiles like stone-coated steel are often the right call for older Danville roofs that weren’t built for heavy tile. If we find structural problems during deck inspection, you see photos and a written change order before any work continues.
Full metal roofing installation in Danville runs $15,000 – $40,000 depending on roof size, pitch, roofline complexity, existing deck condition, and the panel type you choose. Standing seam and stone-coated steel sit near the top of that range. Call (888) 419-3650 for a written line-item estimate – it’s free, and the number you see is the number you pay.
Our metal roofing work is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right, one of the longest workmanship guarantees in residential construction. Panel manufacturer warranties sit alongside that. Both are stated in writing in your estimate. Call (888) 419-3650 with questions – a live person answers, 24/7.
Schedule a Free Metal Roofing Estimate in Danville
A free on-site estimate is the first step. We walk the roof, measure the pitch and square footage, and give you a written line-item quote with a fixed price and no change orders. Calls are answered by a live person, 24/7, so call (888) 419-3650 whenever it’s convenient for you. From foundation to finish line, the team at Groundwork Construction Co. handles metal roofing in Danville and does it right.
Written by the team at Groundwork Construction Co.