Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Window Replacement in Danville, CA: What It Costs and How Long It Takes
Window replacement in Danville typically runs $4,500 – $15,000 for a whole-house package, and most single-family jobs are finished in one to three days once the units arrive. The scope is straightforward: remove the old sashes and frames, check and repair the rough opening, install and flash the new units, seal and trim. On a 1960s – 1990s Danville home you’ll usually be matching existing stucco returns and trim profiles, which is where the real labor sits. Call (888) 419-3650 to schedule a free on-site estimate.

How our Danville window replacement process actually runs, stage by stage
Window replacement is a sequencing job. The order matters as much as the product, and knowing what happens on which day is how you plan around furniture, pets and work-from-home schedules.
Stage 1: On-site measure and product selection (day of estimate, 60 – 90 minutes)
We open and close every window, check for rot at the sill and jamb, look at how the stucco ties into the frame, and measure each opening. You decide frame material, glass package and interior trim finish at this stage. This is also when we flag which openings are standard replacements and which will need rough-opening repair, because that changes the schedule.
Stage 2: Order and permit (roughly 2 – 5 weeks)
Made-to-order units take the longest. Standard sizes arrive faster than custom. If your project triggers a permit, we pull it before any demolition, and the inspection is scheduled after installation. You’ll want to confirm HOA approval here if your Danville community requires it, since architectural review can add one to four weeks and it happens before ordering, not after.
Stage 3: Prep and demo (day 1, most of the day)
Floor protection goes down first. We remove interior trim, cut back the old frame if it’s a full-frame replacement, and pull the old unit out. On stucco homes we cut the exterior finish clean and square rather than tearing it, which keeps the patch small. Rot at the sill gets repaired or sistered before anything new goes in.
Stage 4: Install, flash and seal (days 1 – 2)
New units get set, shimmed and plumb, then flashed at the head and sill, foamed at the perimeter, and sealed. This is the part that decides whether you get a dry window in ten years, so we don’t rush it. Full-frame jobs take longer than insert replacements because the exterior finish has to be tied back in and the interior drywall returns rebuilt.
Stage 5: Trim, stucco patch, inspection and walkthrough (days 2 – 3, plus cure time)
Interior trim goes back, the exterior patch gets finished, and we walk every opening with you: operation, locks, screens, caulk lines. If a permit was pulled, we meet the inspector after. Exterior sealant needs a cure window before the first heavy rain, so we tell you the date to leave it alone.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Window replacement options you’ll choose between in Danville
Most of the decision comes down to four picks. Each one trades cost against how long the window lasts and how much exterior work it demands.
- Insert vs full-frame replacement: Insert replacements reuse the existing frame and cost roughly 30 – 40% less, but only work when the frame is sound and square. Full-frame replacement is the right call on older Danville homes with deteriorated frames or when you’re changing the opening size. It costs more and requires stucco and drywall repair.
- Vinyl vs fiberglass vs wood-clad frames: Vinyl is the lowest-cost choice and holds up well in a hot inland climate, though color options are limited and it can’t be repainted easily. Fiberglass costs a step more and handles heat expansion better. Wood-clad aluminum is the premium pick and the only one that truly matches stained interior trim in a custom home.
- Glass package: Double-pane Low-E is the baseline for California’s Title 24 requirements and makes sense everywhere in the Tri-Valley. Triple-pane costs more and mostly helps on west-facing glass that takes the worst of the afternoon sun. Tempered glass is required near doors and at floor-level windows.
- Andersen vs Marvin: Andersen’s 100 and 400 Series cover the standard replacement market well. Marvin is where we point homeowners who need custom sizes or a taller, thinner profile on a Mediterranean or ranch elevation.
What window replacement costs in Danville, CA
Whole-home window replacement in Danville runs $4,500 – $15,000, and a single opening typically lands a few hundred dollars up to around $1,500 depending on size, glass and frame. Here’s how the number moves.
- Number and size of openings: Ten standard windows sit near the low end. Twelve to sixteen openings with large view windows push toward the high end.
- Insert vs full-frame: Inserts save on labor. Full-frame adds stucco cutting, flashing and interior drywall repair.
- Frame and glass grade: Vinyl with standard Low-E is the base. Fiberglass, wood-clad or triple-pane adds to the total.
- Existing condition: Rot at sills and jambs, cracked stucco or out-of-square openings add repair time.
- Permit and HOA scope: A permit and inspection add cost and time. HOA architectural review adds calendar time, not usually labor.
Your written estimate is line-item: each opening, the unit spec, trim work, flashing and sealing, stucco patch and permit fees. Upfront pricing means the number you see is the number you pay. What’s not included is any structural change discovered after demo, since nobody can price what’s still hidden inside a wall. Call (888) 419-3650 for an exact quote; estimates are free.

See the difference
Before
After
Before
After
Before
AfterWhat Danville homes specifically do to a window replacement job
Danville is a built-out, high-value Tri-Valley suburb, and almost everything we do here is replacement on existing homes rather than new builds. That changes the job. In the established 94526 core you’re cutting new units into mature stucco on 1960s – 1990s ranch and Mediterranean homes, so trim matching and clean stucco patching drive how the finished window looks against the rest of the house. Owners here are improving homes worth well over $1.5 million and intend to stay, which is why we don’t shortcut the flashing.
The 94506 hillside side, including Blackhawk and the Tassajara corridor, plays by a different set of rules. It sits in WUI fire-zone territory, so replacement windows and doors in that zone often need fire-rated assemblies and careful detailing for defensible space. The inland heat is the other Danville factor: intense summer sun on west-facing glass is what kills seals and fades interior finishes faster than in fog-cooled Bay Area cities, so the Low-E spec matters more here than it does closer to the bay.
We cover the whole of Danville, from the flat core up to the gated hillside communities, and if the project grows into a larger exterior scope, that’s part of a full Windows & Doors in Danville plan. See our Windows & Doors service for the wider picture. Homeowners often pair this with Vinyl Fence in Danville to finish a backyard renovation, or Aluminum Fence in Danville where the goal is a low-maintenance, fire-conscious perimeter.
Serving Danville, CA – Our Local Coverage Area
We serve Danville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Window replacement in Danville
A typical three-to-five-opening job is done in one day, and a whole-house replacement runs one to three days of on-site labor. Add two to five weeks for made-to-order units and the permit before we start. If your community requires HOA architectural review, plan another one to four weeks.
Often yes, depending on the scope and whether you’re changing the opening size. Full-frame replacements and anything altering the rough opening usually require a permit and inspection. We check the requirement for your address before ordering and handle the paperwork for you.
In nearly every case, yes. A standard replacement doesn’t touch plumbing or framing unless we find hidden rot or a damaged header during demo. That’s the one variable nobody can price in advance, and we tell you before any extra work starts.
Whole-home replacement runs $4,500 – $15,000 here, and a single opening is a few hundred to about $1,500 depending on size and frame. Insert versus full-frame, glass grade and existing condition are the main movers. Call (888) 419-3650 for an exact quote; estimates are free.
Every installation we do is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. Manufacturer warranties on the units themselves vary by brand and glass package. If the price changes for any reason, it’s because you approved the change first.
Get a free window replacement estimate in Danville
Call (888) 419-3650 to schedule a free on-site estimate for window replacement in Danville. We’ll measure every opening, check the frames and sills for rot, confirm what the permit and any HOA review will require, and hand you a written line-item quote before you commit to anything. A live person answers, 24/7. Background-checked, uniformed technicians handle the install, and every job is backed in writing.
Written by the team at Groundwork Construction Co.