Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Alamo, CA: What It Runs and How Long It Takes
A wrought-iron fence in Alamo typically costs $3,500 to $9,000 and takes three to five working days from layout to final coat, depending on length, height, finish, and whether the run follows flat ground or a slope. Most of that time is fabrication lead time and curing, not digging. Call (888) 419-3650 for a free on-site estimate and a written line-item quote before anything gets ordered.

How We Build an Iron Fence in Alamo, Step by Step
Iron work is less forgiving than wood. The layout is set once, the posts are set in concrete, and every panel after that has to match the first one. Here’s the actual sequence we run, with the decisions that land on you at each stage.
Stage 1: On-site measure and layout (day 1, about two hours)
We walk the property line with you, confirm where the fence sits relative to recorded boundaries, and check for buried irrigation, low-voltage lighting, septic lines, or gas runs. On Alamo’s larger parcels, the property line itself is often the biggest question, so bring any survey you have. You decide the run, the gate locations, and the height at this stage; nothing is ordered until you sign off.
Stage 2: Fabrication and finish selection (days 2 to 10, off-site)
Panels, pickets, and posts are cut and welded to the confirmed dimensions, then finished in either a powder coat or a hand-applied paint system. Powder coating adds roughly $8 to $14 per linear foot over standard paint and holds up far better against the San Ramon Valley sun. You pick color, picket spacing, and finial style here. This is the longest stretch of the job, and it happens before a single hole gets dug.
Stage 3: Demolition and prep (day 1 on-site, half a day)
If an old fence comes out, we remove it, pull posts, and haul it off. We mark utility locations before any digging and set string lines to the final grade. On sloped lots, this is where paneling strategy gets decided: stepped panels versus racked panels, which changes both the look and the fabrication order.
Stage 4: Post setting and panel install (days 2 to 3)
Posts go into concrete footings sized to height and wind load, then cure before panels hang. Panels are set, leveled, and welded or mechanically fastened, and gates are hung and adjusted for swing and latch alignment. Expect a short cure window before the fence carries any real load.
Stage 5: Finish touch-up, inspection, and walkthrough (final day)
We touch up weld points and scratches, check every gate, and walk the run with you. We leave touch-up paint with you for later nicks. Most jobs wrap in a single visit for install once fabrication is done.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Iron covers a wider spread than most homeowners expect. The choice drives both the price and how the fence ages.
- Genuine wrought iron: hand-forged, heavier, and the traditional estate look. Highest cost per foot and the longest service life, with real repairability by a welder. Suits the long frontage on Alamo’s estate lots.
- Steel with an iron look: welded steel panels finished to read as wrought iron. Strong, more uniform, and generally the workhorse choice for most residential runs. Priced around the middle of the range.
- Aluminum: lighter, rust-proof, and the budget end. Holds up well in dry summers but feels less substantial and dents rather than bends. Honest trade-off: cheaper, less presence.
- Powder coat vs. paint: powder coat resists fading and chipping better in inland heat; paint is easier to touch up and cheaper upfront.
- Height and picket spacing: 4-foot decorative runs cost less than 6-foot privacy-height iron, and tighter picket spacing adds material and labor.
- Gates: a pedestrian gate is simpler than a wide driveway gate, and automation adds hardware cost and a power run. Often paired with Patios, Walkways & Pool Decks in Alamo when the entry is being redone at the same time.
What an Iron Fence Costs in Alamo, CA
Most residential iron fence projects here land between $3,500 and $9,000. The low end is a short aluminum or light steel run on flat ground; the high end is a long steel or wrought-iron run with a wide gate and powder coat. Five things push the number:

- Linear feet and height: the biggest lever. Doubling the run roughly doubles material and labor.
- Material grade: aluminum sits at the bottom, welded steel in the middle, hand-forged wrought iron at the top.
- Grade and slope: hillside lots need racked or stepped paneling and deeper footings, adding labor.
- Gates and automation: a driveway gate with hardware and a power run is a meaningful line item on its own.
- Old fence removal and access: long private driveways and tight hillside access slow hauling and digging.
A written estimate lists panels, posts, footings, finish, gates, removal, and haul-off, plus any permit cost. It typically excludes landscaping repair, utility relocation, and future paint touch-ups. The number you see is the number you pay; there are no change orders mid-job.
See the difference
Before
After
Before
After
Before
AfterWhat Alamo Homes Specifically Do to This Job
Alamo is unincorporated, so a fence project here runs through Contra Costa County building rather than a city hall, and on hillside parcels off Stone Valley Road the county often wants to see engineering for anything that acts like a retaining or wind-load structure. That’s a different review path than a flat-lot project in Danville. The housing stock matters just as much: custom ranch and Mediterranean estates built from the 1950s through the 2000s on half-acre to several-acre parcels, with long private driveways and detached outbuildings. Those long driveways mean iron frontage runs measured in hundreds of feet, not dozens. The Diablo-wind exposure and wildfire-hardening expectations shape material choices too; noncombustible metal makes sense on a defensible-space perimeter. Older outbuildings and property-line ambiguity turn up often. If your project extends beyond the fence, we cover Alamo for the full range and pull the county permits and pass inspection on each.
Serving Alamo, CA – Our Local Coverage Area
We serve Alamo and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Iron Fence in Alamo
Most jobs take three to five working days on site, with two to three weeks of fabrication and finish lead time before that. The install itself is quick once panels arrive; the wait is fabrication and coating. Call (888) 419-3650 for a timeline tied to your specific run.
Often yes, because Alamo is unincorporated and Contra Costa County reviews fence and gate work, especially taller runs, gates, and anything on a slope or near a retaining structure. The county, not a city, issues it. We pull it and pass inspection; call us for a free check on your project.
Usually yes. Iron posts go into shallow concrete footings, so underground utility location before digging keeps irrigation, septic, and low-voltage lines clear. A pipe or septic line in the run gets stepped around in layout, not relocated. Call (888) 419-3650 and we’ll flag it at the estimate.
Expect $3,500 to $9,000 for a typical residential run, with long frontage, a wide automated gate, or powder coat pushing toward the top. Material grade and slope drive most of it. Call for a free line-item quote.
Every iron fence we install is covered by our 730-Day Done Right Promise: if it isn’t right, we make it right. If you’re also expanding the property with an outbuilding, homeowners often pair this with ADU Design & Permitting in Alamo and Fence Installation in Alamo as one coordinated project. See the full Fence Installation scope for how the pieces fit.
Get a Free Iron Fence Estimate in Alamo
Call (888) 419-3650 for a free on-site estimate on your iron fence in Alamo. A live person answers around the clock; you’ll get a walkthrough of the run, material options with real pricing, and a written line-item quote with no surprises. Financing at 0% for 18 months and $1,000 off projects over $10,000 are available.
Written by the team at Groundwork Construction Co.