Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Danville, CA: What the Job Actually Involves
An iron fence in Danville runs $3,500 – $9,000 for most residential properties, and a typical install takes two to four days once materials are on site. Wrought iron or welded steel panels get set on concrete footings, then finished with a rust-inhibiting primer and topcoat. Call (888) 419-3650 for a free on-site estimate. Iron fencing suits Danville’s larger lots well because it defines a boundary or protects a pool without walling off the view, which matters on the hillside parcels and half-acre yards common here.

How We Install an Iron Fence: Day by Day
Iron fencing isn’t a one-trip job the way a stock panel fence can be. The sequence runs in five stages, and each one has a decision point for you.
- Stage 1 – Measure and layout (day 1, half a day). We walk the property line, confirm setbacks, and mark gate posts and corners. You decide fence height and where gates land. On larger Danville lots, gate placement for vehicle access and equipment often drives the whole layout.
- Stage 2 – Utility locate and footing prep (day 1, half a day). Before any digging, we call for utility locating so irrigation lines, gas, and electrical are marked. Post holes are dug to depth and set on concrete. Footings cure best overnight, so this ends the first day.
- Stage 3 – Panel and post setting (days 2 – 3). Posts go in plumb, panels get hung and leveled. This is where the fence’s strength lives: spacing, footing depth, and anchor hardware all determine whether it stays tight after a decade of summer heat. You confirm gate swing direction here.
- Stage 4 – Gates and hardware (day 3). Gate frames get hung, latches and hinges mounted, and self-closing hardware set if the fence guards a pool. This is the stage that separates a fence that works from one that sags.
- Stage 5 – Finish and walkthrough (day 4). Touch-up coat, cap rails, and a final walk of the whole run with you. Any adjustment happens before we leave.
Homeowners frequently pair a new iron run along the front with a Patios, Walkways & Pool Decks in Danville project so the gate and the hardscape get coordinated in one schedule. If the fence sits along the property line of a planned new structure, it’s often part of a full Fence Installation in Danville scope sized to the whole lot.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between Before We Order
Iron fencing isn’t one product. Most Danville buyers choose between three material paths and a handful of finish and hardware decisions, and each carries a real trade-off.
- Wrought iron (traditional). Hand-forged look with a real heft. Best fit for established properties where the fence should read as part of the architecture. Heavier and pricier; requires periodic recoating.
- Welded steel panels (prefab). The most common path for new runs. Uniform, faster to install, and the coatings have improved. Suits modern and ranch styles; pick a reputable finish system or rust shows within a few seasons.
- Powder-coated aluminum that mimics iron. Lighter and rust-resistant, which helps on exposed hillside lots. Lower cost than wrought iron; it won’t match the visual weight of a real iron fence.
On finishing, the two honest choices are a shop-applied powder coat, which lasts longest, or a field-applied primer and topcoat, which is more flexible on complex ornamental designs. Hardware matters too: self-closing hinges for pool-adjacent gates, and a strong latch that survives kids and dogs.
What Iron Fence Costs in Danville, CA
Expect $3,500 – $9,000 for a residential iron fence in Danville. The low end covers a short run of welded steel with basic hardware; the high end reflects a long run of heavy wrought iron with multiple gates and a shop-applied finish.
Five variables move that number:
- Linear feet and height. A 4-foot run along a side yard costs far less than a 6-foot boundary run around a half-acre lot.
- Gate count and type. Each gate adds hardware and frame. Vehicle gates cost more than pedestrian ones.
- Material grade. Wrought iron sits at the top; powder-coated aluminum and prefab steel sit lower.
- Site conditions. Sloped terrain, tight access, and buried utilities all add labor.
- Finish and coating. A shop-applied powder coat costs more upfront but cuts recoating later.
A written estimate from us itemizes posts, panels, gates, hardware, coating, and any footing work. Not included unless specified: irrigation line repair if a line is hit after the locate, hauling away mature shrubs, and painting of any wall or hardscape adjoining the fence.

See the difference
Before
After
Before
After
Before
AfterWhat Danville Homes Specifically Do to This Job
Danville’s housing stock shapes iron fence work in ways a generic install doesn’t account for. Most properties here are 1960s – 1990s custom and semi-custom homes on large lots, with stucco and tile-roof California ranch and Mediterranean styles. That means the fence usually runs a long way along an established, mature landscaped lot, and matching the scale of a $1.5M-plus home matters more than it would in newer tract neighborhoods. In the flat, established 94526 core, the fence often tucks between mature trees and existing hardscape, so layout takes more care. On the hillside 94506 side, including the gated homes around Blackhawk and the Tassajara area, WUI fire-zone considerations and sloped ground change footing depth and access. We cover Danville including 94526 and 94506, and the two sides of town get a different playbook on both footing and finish.
Serving Danville, CA – Our Local Coverage Area
We serve Danville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Danville
Most residential iron fence installs in Danville take two to four days once materials arrive; larger lots and multiple gates push toward the upper end. The first day handles layout, utility locate, and footings, then panels and gates follow.
It depends on height, location on the lot, and whether the fence guards a pool. We check the requirement for your specific property as part of the estimate, so you know before we order anything.
Usually yes. We lay out around plants and hardscape where the footing allows. If a footing lands on a mature shrub or a wall, we flag it before digging so you can decide.
Most residential jobs run $3,500 – $9,000, depending on length, height, gate count, material, and site conditions. Call (888) 419-3650 for an exact quote – the estimate is free.
Every job is backed by our 730-Day Done Right Promise: if it’s not done right, we make it right. That covers workmanship, so settling posts and misaligned gates get corrected.
Get a Free On-Site Estimate for Your Iron Fence in Danville
Call (888) 419-3650 and a real person answers, day or night. We’ll set a time to walk your property, measure the run, and talk through material and gate options. You get a written, itemized estimate with fixed pricing and no change orders. If your project touches an ADU or addition on the lot, ask about ADU Design & Permitting in Danville while we’re on site.
Written by the team at Groundwork Construction Co.