Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Concord, CA: What It Costs and How It’s Built
An iron fence in Concord, CA typically runs $3,500 – $9,000 for a typical residential run, installed with set posts, a real footing and a finish that survives the valley’s dry summers. Most jobs take three to five working days from layout to cleanup. Call (888) 419-3650 and we’ll walk your property, measure the run honestly, and put a written line-item number in your hands before anyone swings a shovel.

How We Build an Iron Fence, Start to Finish
Iron work rewards patience at the front end. Skip a step here and you’ll see it in a leaning post or a bubbling finish two winters later. Here’s the actual sequence, with what each stage takes and what we need from you.
Stage 1: On-site measure and layout (day 1, half a day)
We walk the property line with you, confirm the actual lot boundary against your plat or survey, and mark every post location with paint or stakes. On older Concord lots we sometimes find the fence line doesn’t match the property line by a foot or more, and that conversation has to happen before anything is ordered. You decide fence height, gate placement and which side faces out. That’s also when we flag any utility locates that need to be called in before digging.
Stage 2: Demo and site prep (day 1 – 2)
If an old fence is coming out, that happens now: tearing down panels, pulling old posts and footings, and hauling it off. Sloped yards toward the foothills are the ones that eat time here, since post height has to be stepped or racked to follow grade without leaving a gap under the panels. You decide whether any existing concrete, planter beds or irrigation lines stay or go.
Stage 3: Post footings and curing (day 2 – 3)
Posts get set in augured holes with concrete footings below your frost line, plumb and braced, then left to cure. Iron is unforgiving – a post set an inch off-plumb stays off-plumb for the life of the fence. This is the slowest-feeling day because nothing visible happens, and it’s the one we don’t rush. You don’t have to decide anything; you just have to let the concrete do its work.
Stage 4: Panel hang and hardware (day 3 – 4)
Once footings are hard, panels go up, gates get hung with proper hinges and a latch that actually lines up, and everything gets tensioned and checked for square. Adjustable hinges on the gates matter more than people expect, because iron doesn’t give the way wood does, and gate sag is the number one callback on this job.
Stage 5: Finish, touch-up and walkthrough (day 4 – 5)
We touch up every scratched weld and cut end, confirm the finish coat is even, and walk the run with you. You sign off on gates, latches and the finished height. Any punch items get scheduled before we pull off the site.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Choose Between
The two big forks in the road are material type and finish, and they drive both the look and the price.
- Wrought iron (traditional): Real forged or solid-bar iron, welded or riveted. The heaviest look, the longest life, and the top of the price range. It suits a period home or a lot where the fence is meant to read as architecture, not just a boundary.
- Ornamental steel: The most common choice today. Steel bar with a forged look, welded panels and a powder-coat finish. Nearly the same appearance as wrought iron at a lower cost, and it holds up well in the East Bay climate.
- Aluminum (steel-look): Lighter and rust-resistant, easy to maintain, less expensive – but it won’t take a hit the way steel will. Fine for a decorative run, less so for a busy driveway gate.
- Finish: Powder coat is the standard and the most durable; a bare or painted finish costs less up front and asks for repainting every few years. For Concord’s hot, dry summers we lean powder coat every time.
- Configuration: Height (4 ft, 5 ft or 6 ft), picket spacing, finial style, gate style and whether the run steps or racks on a sloped yard. Each of these is a real line item, not a rounding error.
Brands matter most on the finish and hardware side. We work with established fence and gate hardware lines and will never spec a finish we haven’t seen hold up through a few summers.

What an Iron Fence Costs in Concord, CA
Residential iron fence in Concord lands between $3,500 and $9,000 for a typical front or side-yard run. That’s a real range, not a teaser – and here’s what moves a job to the low end versus the high end.
- Linear footage: The biggest lever. A short side-yard run sits near the bottom; a full front perimeter plus a driveway gate sits near the top.
- Material grade: Aluminum or lighter ornamental steel lands toward $3,500 – $6,000; heavier steel or true wrought iron moves toward the $7,000 – $9,000 end.
- Existing conditions: Removing an old fence, breaking out old footings, or dealing with rocky or sloped ground adds labor. A clean, level, fence-free yard stays near the low end.
- Gates: A single pedestrian gate is modest; a wide driveway gate with heavier hinges and a self-closing latch costs meaningfully more.
- Finish and height: Powder coat over a bare finish, and 6 ft over 4 ft, each push the number up – usually a few hundred dollars per run, not thousands.
Your written estimate lists the footage, the material grade, the finish, gate count and hardware, plus demo and haul-away where it applies. It does not include utility relocation, extensive concrete work, or repairs to an existing wall or retaining structure – those get priced separately once we see them. Upfront pricing, no surprises, and the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Concord Homes Do to an Iron Fence Job
Concord’s housing stock is the reason this job has its own quirks. The city is dominated by post-WWII and 1950s – 70s single-story ranch tract homes, and in those older tracts we regularly find original 1950s – 60s additions built without permits – which means the “back corner” of the lot isn’t always where the plat says it is. Add the valley-to-foothill gradient, with marine-layer moisture on the west side and extreme summer heat uphill, and you get two different fences within a mile needing two different finishes. Along the downtown and BART corridors the mid-century apartments and condos often share fence lines with neighboring parcels, so boundary confirmation matters before we dig. Hillside lots toward the Mount Diablo foothills bring slope, drainage and wind exposure that flat-lot fences never see. And because the East Bay now leans on seismic retrofits for older unbolted foundations, we plan post footings that won’t fight a future retrofit and route gates so they don’t block access to the crawlspace or foundation work. Whether we’re covering the 94518, 94527, 94519 and 94522 ZIPs, we pull the required permits and schedule the inspection before the job is called done.
Serving Concord, CA – Our Local Coverage Area
We serve Concord and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Iron Fence in Concord
Most residential iron fence jobs in Concord take three to five working days from layout to final walkthrough. Larger runs, multiple gates or a good deal of demo push it toward the higher end. Call (888) 419-3650 for a firm timeline once we’ve measured.
It depends on height and location – front-yard fences and taller runs typically need a permit, while some interior or side-yard fences may not. We handle the permit application and inspection scheduling for you, so you’re not chasing the city. Call (888) 419-3650 and we’ll tell you what your specific lot needs.
Usually, yes. We augur post holes rather than trench the whole run, and we call in utility locates before digging. If a line or a concrete feature sits in the way, we’ll flag it during the on-site measure and price the workaround up front rather than mid-job. Call (888) 419-3650 to schedule a walk-through.
A heavier driveway gate typically adds a few hundred to a couple thousand dollars to the job, depending on width, weight and hardware. It’s a line item on the estimate, not a surprise. Call (888) 419-3650 for an exact quote – estimates are free.
Every iron fence we install is backed by our 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship; the finish and hardware carry their manufacturer warranties. Call (888) 419-3650 and we’ll put the terms in writing before you sign.
Get a Free Iron Fence Estimate in Concord
Call (888) 419-3650 for a free on-site estimate. A live person answers, day or night, and can book a walk-through that fits your schedule. We’ll measure your run, talk through material and finish options, and hand you a written line-item quote you can compare against anyone. Part of a full Fence Installation in Concord project, or paired with a new walkway under our Fence Installation service? Either way, you get the same upfront number and the same 730-Day Done Right Promise covering Concord. Homeowners often pair this with Patios, Walkways & Pool Decks in Concord or an ADU Design & Permitting in Concord job. One call, one plan.
Written by the team at Groundwork Construction Co.