Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Bay Point, CA: What It Takes and What It Costs
Most iron fence projects in Bay Point run $3,500 – $9,000, and a typical side-yard or front-boundary run takes two to five days on site once the material is fabricated. Iron fencing here means painted or galvanized steel and wrought-iron-style panels set in concrete footings, built to hold up against the delta wind that pushes through this side of Contra Costa County. Call (888) 419-3650 for a free on-site estimate; we’ll measure your line and give you a written number.

How We Build an Iron Fence in Bay Point, Step by Step
An iron fence isn’t a picket job where you show up with posts and panels and finish by lunch. Steel has to be ordered, cut, welded and finished to your line, and the ground has to be right before any of that goes in. Here’s the actual sequence.
Stage 1: Site walk and layout (day 1)
We walk the property line with you, confirm where the fence runs, and check what’s under the ground: irrigation lines, old footings, utility markings. Bay Point properties on sloped or bay-fill lots often have soft spots that need deeper footings, and we identify those before ordering steel. You decide the run, the height and where the gates land. This visit takes about an hour.
Stage 2: Permits and material order (days 2 – 10)
Because Bay Point is unincorporated, fence permits go through Contra Costa County, not a city building department. Count on roughly a week to two weeks for the county review depending on scope; we pull it and handle the submittal. Steel panels and posts get ordered at the same time, so fabrication and permitting run in parallel rather than back to back. This is where the fence spec gets locked: panel style, post size, finish.
Stage 3: Demolition and footing prep (day 1 on site)
If there’s an old fence, we tear it out and haul it away. Post holes get dug to depth, set with rebar and filled with concrete. On a standard 6-foot iron fence, posts go about 24 to 30 inches deep; on exposed runs that catch delta wind, we go deeper. Holes cure for 24 to 48 hours before the panels go up, and that cure time is non-negotiable.
Stage 4: Panel and gate install (days 2 – 4 on site)
Panels get set, leveled and welded or bolted to the posts. Gates get hung with hinges rated for the span, and latches get aligned so they close clean. A 100-foot run takes a crew a couple of days; longer runs and multiple gates stretch to four. You’ll walk the line with the crew lead before they leave for the day.
Stage 5: Inspection and finish touch-up (final day)
We touch up any weld points or scratches with matching paint, confirm gate swing, and meet the county inspector if the permit calls for one. Then we walk it with you and you sign off. Every iron fence we install is covered by our 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Choose Between
Three decisions drive most of the cost and look on an iron fence, and each one has a real trade-off.
- Wrought-iron-style steel vs. aluminum: True steel gives you weight, security and a lifespan measured in decades, and it’s what most Bay Point homeowners want on a front boundary. It costs more and needs touch-up painting every few years. Aluminum is lighter, won’t rust, and costs less, but it dents and doesn’t feel as substantial in the hand.
- Finish: Powder-coated black is the standard and holds up well against the salt air that drifts in off the Delta. Galvanized-then-painted gives you more rust protection on the bottom rails where moisture sits. Bare or primed-only finishes look unfinished within a year here.
- Height and spacing: A 4-foot fence reads as decorative; a 6-foot fence with tighter picket spacing is a security fence. Spacing between pickets and post size both change the steel order, so decide before fabrication, not after.
- Gates: A single walk gate is standard. A double drive gate needs heavier posts and a different hinge setup, and it’s where budgets most often creep.
What Iron Fence Costs in Bay Point, CA
Plan on $3,500 – $9,000 for an iron fence in Bay Point, all in, including materials, footings, labor, permit and cleanup. Where you land in that range depends on five things:

- Linear feet: Most of the spread. A short front run sits near the bottom; a full perimeter pushes the top.
- Height and picket density: Taller, tighter fences use more steel and heavier posts.
- Grade and finish: Powder-coated steel costs more than primed steel up front and less over time.
- Site conditions: Sloped ground, soft bay-fill soil and old footings to remove all add labor.
- Gates and permit scope: Multiple gates and county review hours add to the total.
A written estimate from us breaks out material, footing, labor and permit line by line so you can see exactly what the number is made of. What it doesn’t include: hauling off landscaping you want saved, or repairing an irrigation line we uncover and that wasn’t marked. We flag those before we start.
See the difference
Before
After
Before
After
Before
AfterWhat Bay Point Homes Specifically Do to This Job
Bay Point sits where the delta breezes meet the Diablo Range, and that wind changes how an iron fence gets built here. Posts that would be fine on a sheltered lot in Concord need deeper footings and heavier steel on an exposed run facing the Delta, because a fence that catches a spring gust at the wrong angle will lean within a season. The soil matters too: much of the housing stock dates to the post-WWII and mid-century tract era, and the soft bay-fill ground under some of it means footing depth gets checked, not assumed. And because Bay Point is unincorporated, there’s no city hall to walk into – the permit goes to Contra Costa County, which affects how long the paperwork takes before a crew can start. We see fences that failed at the posts far more often than at the panels, which is why we spend the time on the footings.
Serving Bay Point, CA – Our Local Coverage Area
We serve Bay Point and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Bay Point
Two to five days on site for most residential runs, plus one to two weeks ahead of that for Contra Costa County permitting and steel fabrication. The on-site work is quick; the waiting is in the paperwork and the material order.
Usually yes, and it goes through Contra Costa County rather than a city building department because Bay Point is unincorporated. Fence height and placement near property lines and easements have county rules, and we confirm what applies to your line before we order steel. We pull the permit and handle the inspection.
In most cases yes. Footings are dug at the post locations, not trenched along the whole run, so the disruption stays narrow. We cut and reset grass at each post and flag irrigation lines before we dig. If we hit something unexpected, we stop and talk to you first.
Expect $3,500 – $9,000 for a typical residential iron fence, with linear feet, height, finish, gates and site conditions moving the number. A written line-item quote tells you exactly where your job lands. Call (888) 419-3650 for a free on-site estimate.
Every iron fence we install is covered by our 730-Day Done Right Promise. If something isn’t right, we make it right. The steel finish itself also carries the manufacturer’s warranty on top of ours.
Get an Iron Fence Estimate in Bay Point
Call (888) 419-3650 and we’ll set up a free on-site estimate at your Bay Point property. We measure the line, check the soil and site, and talk through steel grade, finish and gate layout. You leave with a written, line-item number and a realistic start date, no pressure and no surprises. Live person answers the phone, day or night. This is often part of a full Fence Installation in Bay Point plan, and homeowners often pair it with Patios, Walkways & Pool Decks in Bay Point or an ADU Design & Permitting in Bay Point project down the road. See our fence installation service and the Bay Point area page to learn more.
Written by the team at Groundwork Construction Co. of Antioch.