Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Danville: What It Costs and How Long It Takes
A tub-to-shower conversion in Danville typically runs $3,500 to $10,000 and takes 5 to 10 working days once demolition starts. The job removes the old tub, reconfigures the drain and valve, waterproofs the wet wall, and installs a walk-in shower pan and surround sized to the existing alcove. Most Danville conversions we quote land in the $4,500 to $7,800 range because the standard 5-foot tub footprint translates cleanly to a 48- or 60-inch shower base. Call (888) 419-3650 for a free on-site estimate.

How a Conversion Actually Runs, Day by Day
We sequence this job the same way every time. Here’s what happens and when.
Stage 1: Site protection and demolition (Day 1)
We lay floor protection from the front door to the bathroom and shut off water at the fixture stops. The tub, surround, valve trim, and any glass come out, then we open the wall to the studs around the wet wall and inspect the framing for rot. In Danville’s 1960s and 1970s homes, we find soft framing under the valve more often than not because older tub surrounds trapped moisture for decades. You decide here whether we replace a section of subfloor or keep the existing one if it tests solid.
Stage 2: Rough plumbing and electrical rough-in (Days 2 – 3)
The drain gets repositioned to the new shower’s center point and the valve body goes in at the correct height for a shower, not a tub spout. If you want a niche, a bench, or a recessed shelf, it gets framed now before anything closes up. This is when you make the biggest layout call: a simple alcove shower, or a curbless entry that requires lowering or relocating the drain. Curbless adds cost but is the smarter choice if anyone in the household has mobility concerns.
Stage 3: Inspection and waterproofing (Days 3 – 4)
Rough plumbing gets inspected before it’s covered. Then we install a bonded waterproofing membrane over the pan and walls. Schluter’s Kerdi system is what we specify most because it bonds directly to the substrate and eliminates the weep-hole failures that plague traditional mud pans over time. The membrane has to cure before tile goes on, so this is a genuine wait day, not filler.
Stage 4: Tile and finish (Days 5 – 8)
Wall tile, floor tile, grout, and sealant happen here. You’ve already picked your tile and fixtures at the estimate stage, so there’s no delay waiting on selections. We set the shower valve trim, install the drain grate, and mount any grab bars or a shower seat now.
Stage 5: Fixtures, glass, and walkthrough (Days 9 – 10)
Showerhead, handheld, glass panel or door, and final caulk go in on the last two days. We water-test the pan, run the valve hot and cold, and walk the finished shower with you before we leave.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices That Shape the Price and the Result
Most of the variation in a Danville conversion comes from four decisions. Here’s the honest trade-off on each.
- Shower base vs. curbless pan: A prefab acrylic or solid-surface base (Sterling makes a solid option) installs fast and costs less. A curbless tiled pan looks better and ages better but adds labor and framing work to lower the drain.
- Acrylic surround vs. tile: Acrylic is the budget-lean choice at roughly $1,200 to $2,500 in materials and cleans up fast. Porcelain or ceramic tile runs $2,000 to $5,000 in materials depending on grade and gives you a finish that reads as custom. In Danville’s higher-value homes, tile almost always wins on resale.
- Valve and trim brand: Grohe and Toto trim packages sit in the middle of the market and hold up well to the hard water we see inland. Budget builder-grade trim saves $200 to $400 but needs replacing sooner.
- Glass enclosure: A fixed panel costs less than a framed door; a frameless door runs higher but opens up a small bathroom visually. This is often where homeowners upgrade.
Tub-to-Shower Conversion Costs in Danville, CA
Expect $3,500 to $10,000 for a tub-to-shower conversion in Danville, with most jobs landing between $4,500 and $7,800. Here’s what moves a quote to the low or high end.

| Line item | Typical range |
|---|---|
| Demo and disposal | $400 – $900 |
| Rough plumbing (drain + valve) | $700 – $1,800 |
| Waterproofing and pan | $600 – $1,500 |
| Tile and setting materials | $1,200 – $3,500 |
| Shower valve, trim, and head | $300 – $1,200 |
| Glass enclosure or door | $500 – $1,800 |
| Permit and inspection fees | $250 – $600 |
The variables that push a job up: relocating the drain more than a few inches, discovering rot or a failed subfloor under the old tub, adding a bench or multiple niches, upgrading to a frameless glass door, or choosing large-format tile that needs a flat substrate and more labor. A written estimate from us lists each line so you see exactly what’s included. What’s typically not included: replacing the vanity or flooring outside the shower alcove, and any structural changes you didn’t ask us to quote.
See the difference
Before
After
Before
After
Before
AfterWhat Danville Homes Specifically Do to This Job
The vast majority of the homes we convert here are 1960s through 1990s custom and semi-custom builds, and that matters. In the flat 94526 core, tubs are frequently set in a tiled platform or a fiberglass surround that’s been hiding moisture behind it for decades. We open those walls expecting to find at least some framing repair, and we quote it as a contingency rather than surprising you mid-job. On the hillside 94506 side toward Blackhawk and Tassajara, homes often have larger primary baths where a conversion is part of a bigger primary-suite project, and that’s where owners frequently pair the shower work with our Bathroom Remodeling in Danville scope or tie exterior work into a Tile Roofing in Danville or Metal Roofing in Danville project while crews are already on site. Permits are required for this job in Danville because plumbing is being altered, and the town inspects the rough plumbing before the walls close. We pull the permit and schedule the inspection ourselves so the conversion doesn’t stall. HOA review, where it applies in the gated hillside communities, is usually limited to exterior venting or window changes, not the shower itself. If your conversion is part of a larger project, that runs through our Bathroom Remodeling service, and you can see the full range of what we cover on our Danville service-area page.
Serving Danville, CA – Our Local Coverage Area
We serve Danville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Tub-to-Shower Conversion in Danville
Most conversions take 5 to 10 working days from demo to walkthrough. Simple acrylic conversions finish closer to 5 days, while tiled, curbless, or large-format jobs run the full 10. Call (888) 419-3650 for a schedule estimate based on your bathroom.
Yes. Because the drain and valve are being altered, Danville requires a plumbing permit and a rough inspection before the walls close. We pull the permit and handle the inspection as part of the job, and the fee is built into your written estimate.
In most cases, yes. Many Danville tubs already have the drain positioned so it lines up with a standard shower pan, which keeps costs low. If the drain sits at the wrong end or too close to a wall, we relocate it, which adds $400 to $1,200 depending on how far it moves.
The range is $3,500 to $10,000, with most jobs landing between $4,500 and $7,800. Tile versus acrylic, curbless versus a standard base, and glass enclosure choice are the three biggest levers. Call (888) 419-3650 for an exact quote, and the estimate is free.
Our work is backed by the 730-Day Done Right Promise on top of any manufacturer warranty on fixtures and materials. If something we installed isn’t right, we make it right, and that’s in writing before work starts.
Get a Free Tub-to-Shower Conversion Estimate in Danville
Call (888) 419-3650 to schedule your free on-site estimate for a tub-to-shower conversion in Danville. A live person answers any hour, and we’ll walk your bathroom, measure the alcove, talk through tile and fixture options, and hand you a written line-item quote with upfront pricing and no surprises. Projects over $10,000 get $1,000 off, and 0% financing for 18 months is available.
Written by the team at Groundwork Construction Co.