Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Paver Driveways in Danville: What to Expect, Start to Finish
A paver driveway in Danville generally runs $7,000 to $18,000 for a typical two-car approach, and most jobs are finished in three to five working days once materials land on site. The work itself is straightforward: tear out the old surface, rebuild the base, compact it in lifts, then set pavers on a sand bed with edge restraint and polymeric joint sand. Call (888) 419-3650 and we’ll walk your driveway, talk grades and drainage, and give you a written line-item estimate before anything gets demoed.

Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
How We Install Paver Driveways in Danville, Stage by Stage
The sequence below is what actually happens. Expect some overlap between stages depending on weather and how much base excavation your lot needs.
Day 1: Demo and excavation
We remove the existing concrete, asphalt or old pavers and haul them off. Then we excavate down to the subgrade – typically 8 to 12 inches below finished grade for a residential driveway that sees cars and the occasional delivery truck. This is the day your driveway looks its worst. Plan to park on the street or in the garage for the duration.
Days 1 – 2: Base prep and compaction
Crushed aggregate base goes in lifts of about 3 to 4 inches, each one watered and compacted before the next. This is the stage nobody photographs and everybody should care about. A paver driveway on a weak base fails at the edges and along the wheel paths within a few seasons. We check slope here too, so water runs to the street or a drainage point instead of pooling against the garage slab.

Day 2 – 3: Edge restraint and the sand setting bed
We set the edge restraint on a concrete curb, then screed a 1-inch sand bed to grade. You’ll have already picked your paver pattern and color by this point – that decision has a lead time of roughly one to two weeks on most Belgard and Techo-Bloc lines, so it’s worth locking in early. Changing color after the order goes in usually means a delay, not just a restocking fee.
Days 3 – 4: Setting the field and cutting
Pavers get laid from a fixed reference line, with cuts at the garage apron, edges and any curves. On a Danville slope lot in the 94506 hillside zones, we spend real time on transitions and step-downs at the street. If your driveway ties into an existing walkway or apron, that junction is where the cut quality shows. You’ll be asked to approve the field pattern on a small dry-laid sample before full installation.
Day 4 – 5: Polymeric sand, compaction and cleanup
We sweep polymeric joint sand into the joints, activate it with a light water mist, run a final plate compactor pass and wash down the site. The driveway is drivable once the sand cures enough for foot and vehicle traffic – usually within 24 hours, though we’ll tell you the exact window on your job.
Serving Danville, CA – Our Local Coverage Area
We serve Danville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
The Paver Options You’ll Actually Choose Between
Most buyers land on two or three real candidates after seeing samples. Here’s the honest read on each.
- Concrete pavers (Belgard, Tremron): The default choice for a reason – strong, repairable, wide color range, and individual units can be pulled and reset if a utility trench opens later. Cost sits in the middle of the range. Surface texture holds up well under Danville’s intense summer sun.
- Clay brick pavers: Warm, classic look that suits the Mediterranean and ranch styles common in the 94526 core. More expensive per square foot and harder to match if you need a repair years down the road. Also slicker when Frosty mornings leave a thin ice film.
- Tumbled or antique-finish pavers (Techo-Bloc, Unilock): Softer, older-looking surface that hides tire marks and mild staining well. Slightly higher cost than standard run. Good fit if your home already reads as Mediterranean.
- Permeable paver systems: Open-graded joints and a stone reservoir below handle runoff on-site. In the hillside WUI zones where drainage and defensible space both matter, this can simplify the site plan. Higher installed cost, more base excavation, and you’ll need to stay on top of joint cleaning.
- Pattern choices – running bond, herringbone, basketweave: Herringbone interlocks best under turning tires and is worth the extra cutting time on a driveway. Running bond is cheaper and reads cleaner on a long, straight approach.
If the driveway is part of a full Driveway & Pavers in Danville project with a front walk or motor court, we’ll spec the whole job together so the pavers, color and pattern carry through.
See the difference
Before
After
Before
After
Before
After