Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Livermore, CA: What the Job Really Involves
Custom & geometric windows in Livermore usually means one of two things: a shape that isn’t stock (arches, half-rounds, trapezoids, angled corner units, true-radius bays) or a window sized to an opening that no catalog unit fits. Expect 4 to 8 weeks from template to final trim, and $4,500 to $15,000 for a replacement-scale project, more when structural changes are involved. Call (888) 419-3650 for a free on-site estimate.

How we take a custom or geometric window from measurement to final trim
Custom windows aren’t a truck-roll job. The sequence is fixed, and the homeowner makes a real decision at each stage. Here’s what actually happens.
Stage 1: Site measure and template (day 1, 2 to 3 hours)
We measure the rough opening, check the wall for plumb and square, and photograph the existing trim and interior finish so the new unit lines up. For true-radius and eyebrow windows, we build a physical template of the opening. You decide the window style, the wood or clad finish, and whether the interior trim gets reused or replaced. Bring any HOA design guidelines with you; that’s the stage where they matter most.
Stage 2: Order and lead time (weeks 1 to 5)
Custom shapes are built to order, so lead time is the long pole. Most arched and angled units run 3 to 5 weeks; radius and specialty glazing can stretch past 6. You confirm the final order sheet and the price, in writing, before anything is placed. No surprise additions later.
Stage 3: Demolition and prep (day 3 of the install, half a day)
We pull the old unit, cut back to sound framing, and check for rot, water staining, or a cracked sill. Around windows in older Livermore stock, this is where we find the problems nobody saw, so we handle the repair before the new unit goes in, not after.
Stage 4: Set, flash, and seal (day 3 to 4)
The frame gets set plumb and level, then flashed and sealed to shed water. Geometric units are heavy and awkward, so this is a two-person job with a third on the ground. You don’t need to be home for this stage; we photograph the flashing work and share the images.
Stage 5: Trim, glass, and walkthrough (day 4 to 5)
Interior trim and casing go on, glass is cleaned, and we walk the opening with you: operation, locks, screens, seal. Any touch-up happens before we leave. Everything is covered by our 730-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
For custom and geometric windows, the material and glazing choices are where most of the budget difference lives. Here’s the honest trade-off on each.
- Wood interior with aluminum-clad exterior. The classic pick for arched and radius units on a home with existing wood trim. Warm inside, weather-resistant outside, and easy to paint or stain. Costs more than a pure vinyl unit.
- All-vinyl geometric frames. Lowest upfront cost, impervious to moisture, and a good fit for a tract or infill home in 94551. Fewer finish options, and heavier shapes may not be available in every manufacturer’s line.
- Fiberglass. Holds paint well, expands and contracts far less than vinyl, and takes a true geometric shape without warping. Costs more than vinyl, less than clad wood.
- Glazing package. Double-pane is standard; low-E or argon adds cost but pays back on the west-facing windows that take the worst of a Livermore summer afternoon. Tempered glass is mandatory near a door or a low sill.
- Grid pattern and trim profile. A true divided lite, simulated divided lite, or no grid at all changes the labor and the price. Reusing existing interior trim keeps the budget down; new casing gives a cleaner finish.
What Custom & Geometric Windows cost in Livermore, CA
A single custom shape typically runs $1,200 to $3,500 installed; a whole-home project with several geometric units can reach $8,000 to $25,000. Here’s what pushes a job up or down.

- Shape complexity. A half-round is straightforward; a true radius or an eyebrow unit built to a physical template costs more.
- Opening condition. Rot, cracked sills, or a rough opening that’s out of square add repair labor and material.
- Structural changes. Widening an opening or adding a header moves the job well past a straight replacement and into permit territory.
- Material grade. Vinyl sits at the low end, clad wood at the higher end, and fiberglass in between.
- Trim and finish. Reusing trim lowers the number; new interior casing and a painted exterior add cost.
A written estimate should list the window units, glazing, trim, labor, permit fees if any, and disposal. It typically excludes interior painting, drywall repair beyond a small patch, and any rot repair discovered after demo unless we’ve scoped it up front. If we find rot mid-job, we quote it in writing before touching it, and the price you signed is the price you pay for everything we scoped. Call (888) 419-3650 to start the estimate; it’s free.
See the difference
Before
After
Before
After
Before
AfterWhat Livermore homes specifically do to this job
Livermore sits on the Greenville Fault within the seismically active Livermore Valley, so adding or enlarging an opening in a home that predates modern codes usually triggers more than a window swap. Downtown Livermore (94550) is full of early-1900s to 1950s single-story ranches and Victorians on raised foundations, and a geometric window into a bay or gable there can turn up unreinforced framing or a cripple wall the building department wants retrofitted at the same time. We plan for that on the first visit rather than after the inspection.
Newer homes in 94551 are a different job. The clay-heavy soils under the Livermore Valley have a habit of moving, so we check that rough openings are square before we order a custom unit built to a template, or the window won’t sit right. And hot, dry summers mean the west- and south-facing glass should get a decent low-E coating if you want the room usable in August. If your project grows into structural work or a full exterior update, it may line up with our Windows & Doors in Livermore work or a wider scope under our Windows & Doors service. We cover Livermore end to end, and homeowners often pair a window project with Concrete Driveways & Concrete Work in Livermore or Asphalt Driveways & Resurfacing in Livermore to finish the exterior refresh in one pass.
Serving Livermore, CA – Our Local Coverage Area
We serve Livermore and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Custom & Geometric Windows in Livermore
Four to eight weeks from template to final trim, with most of that in the order and lead time. Install itself usually takes two to three days per opening once the units arrive. Call (888) 419-3650 to get a real timeline for your window.
It depends on whether the frame or the structure changes. A like-for-like replacement in the existing opening typically doesn’t need one; a new opening, a widened opening, or a bay that changes the wall usually does, and on pre-code downtown homes the city may require a seismic upgrade alongside it. We pull the permits and handle the inspections.
Yes, in most cases. If the opening is the right size and the framing is sound, we can drop in a true-radius or angled unit as a direct replacement. When the shape requires a new opening or a header, that’s a different scope, and we’ll say so before you commit. Call (888) 419-3650 and we’ll walk the opening with you.
One custom unit runs $1,200 to $3,500 installed, and a multi-window project reaches $8,000 to $25,000. Shape, material, glazing, and opening condition are the four things that move it. Call (888) 419-3650 for an exact quote, estimates are free.
Workmanship is covered by our 730-Day Done Right Promise: if it isn’t done right, we make it right. The window manufacturer’s own warranty covers the unit and glass, and we register it with you. Calls are answered by a live person 24/7.
Get a free estimate on custom & geometric windows in Livermore
A free on-site estimate starts with a call to (888) 419-3650. We measure the opening, talk through the shape and material options, and leave you with a written line-item price that spells out the windows, trim, labor, and any permits. No pressure and no change orders later. If it’s a project over $10,000, you’ll also see the $1,000-off promotion and 0% financing for 18 months.
Written by the team at Groundwork Construction Co.