Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Aluminum Fence in Alamo, CA: What It Costs and What It Takes
An aluminum fence in Alamo typically runs $4,000 to $10,000 installed, with most of our jobs landing in the $3,500 to $9,000 range once you get past the long-driveway outliers. A standard 150-linear-foot run around a half-acre yard takes two to three days on site, and the fence itself carries a manufacturer finish warranty on top of our 730-Day Done Right Promise. Call (888) 419-3650 and a live person answers, any hour.

How We Build an Aluminum Fence in Alamo, Start to Finish
Aluminum is a product where the installation matters more than the panel. Get the posts and layout right and the fence sits straight for decades. Rush it and you get sag, racking, and gates that drag. Here is the actual sequence.
Stage 1: Site walk and layout (day one, 1 to 2 hours)
We walk the property line with you and stake every corner, gate, and termination point. On Alamo’s larger parcels, this is where we solve the real problem: your line may run along a slope or through a stand of oaks, and the fence has to step or rack to follow the grade. You decide gate locations here, because moving a gate after the posts are set means digging them out.
Stage 2: Utility locate and line confirmation (day one, before digging)
Before a single post hole is dug, we call 811 and confirm your property line. Semi-rural parcels in 94507 frequently have irrigation lines, well feeds, and sometimes septic components near where a fence wants to go. We mark utilities and, if there’s any doubt about the line, we recommend a survey. This step costs you a day of waiting and saves you a trenched water line.
Stage 3: Digging and setting posts (day one and two)
Holes run about 24 inches deep and 8 to 10 inches wide, set in concrete. This is the part that separates a real install from a homeowner kit: aluminum panels are light, but they catch wind across an open valley lot, and the posts carry all of that load. Posts get checked for plumb and line before concrete cures, because once it sets, adjustment means starting over. Fence panels don’t go up until the concrete has cured.
Stage 4: Panel and gate installation (day two or three)
Rails and pickets go on, sections get racked to match the grade, and gates are hung and adjusted for swing. A typical 150-foot residential run is 120 to 160 linear feet, and that is a two- to three-day job for a crew that isn’t cutting corners. Longer runs across an acreage property stretch into a second visit.
Stage 5: Walkthrough and cleanup (final half day)
We walk the whole line with you, check gate latches, confirm post caps and finish, and haul off every scrap. You get the written workmanship guarantee at the end, and your punch list gets handled before we pull out.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices That Actually Change the Fence You Get
Aluminum fences are not one product. Here is what you’ll be picking between, and what each choice really means.
- Residential vs. industrial grade. Residential panels are thinner-wall extrusions suited to keeping kids and dogs in. Industrial grade carries heavier wall thickness and bigger posts, and it’s what we recommend on any run that will see wind load across an open lot or livestock pressure. It costs meaningfully more and holds up far longer.
- Picket spacing and height. Standard 4-foot and 5-foot heights with 3-7/8-inch picket spacing handle most yard enclosures. Tighter spacing or 6-foot height changes both material cost and the wind load on the posts.
- Finish. Powder-coated finishes come in black, bronze, and a range of colors. Black is the classic look against Alamo’s oaks and Mediterranean facades. The finish is what protects the metal, so we favor manufacturers with a real finish warranty over a bargain rack product.
- Racking vs. stepping on slopes. Racked panels follow the grade smoothly; stepped panels hold level sections and drop at posts. On a hillside lot the choice is mostly aesthetic, and it changes the panel count.
- Gates. Walk gates, double driveway gates, and self-closing hardware. A wide driveway gate needs heavier posts and hinges, and that’s a real cost jump.
What Aluminum Fence Costs in Alamo, CA
Most aluminum fence projects in Alamo land between $3,500 and $9,000, and full-perimeter work on a larger estate parcel runs $4,000 to $10,000. What pushes a job toward the low or high end:
- Linear footage. The single biggest driver. A 100-foot backyard run and a 400-foot perimeter run are different projects entirely.
- Grade and terrain. Flat ground is fast. A slope that needs racking, additional posts, or stepped sections adds labor and material.
- Grade of fence. Industrial-grade extrusions and heavier posts push the number up. Cheap rack product pulls it down and sacrifices lifespan.
- Gate count and width. Each gate adds hardware, heavier posts, and adjustment time. Double driveway gates add the most.
- Access. On Alamo’s long private driveways, getting materials to the far fence line takes time, and that shows up on the estimate honestly rather than as a surprise later.
Our written estimates are line-item and fixed: footage, grade, gates, finish, and any site prep. The number you see is the number you pay, and if we discover something mid-job we talk to you before we touch it. Permits, where Contra Costa County requires them, are itemized separately and pulled by us.

See the difference
Before
After
Before
After
Before
AfterWhat Alamo’s Lots and Permitting Do to This Job
Alamo is unincorporated, which changes the paperwork before anyone picks up a shovel. This isn’t Walnut Creek or Danville – there’s no city hall counter here. Fence projects in Alamo go through Contra Costa County, and on hillside parcels off Stone Valley Road, a fence along a slope or property line can trigger questions a flat-lot job never sees. We check the county’s requirements for your specific parcel before we schedule, so the permit question is answered up front rather than mid-install.
The housing stock matters too. This is custom ranch and Mediterranean estate country, with parcels running from half an acre to several acres, long private driveways, detached guest houses, and older outbuildings. What that means for aluminum specifically: perimeter runs are long, gates are often needed at multiple points, and the fence has to hold up against seasonal Diablo winds that push hard on any solid-feeling surface. That’s why we spec industrial-grade posts and heavier wall thickness on exposed runs rather than the lightest rack product. On wind-exposed lines, a heavier aluminum fence is also the safer wildfire-hardening choice than a wood fence, which is a consideration on more properties in this valley every year.
If your fence project is part of a bigger exterior plan, it sits naturally alongside the work in our Fence Installation in Alamo scope, and homeowners often pair it with Driveway Repair & Replacement in Alamo when the access apron needs attention too. Our crews work throughout Alamo and the surrounding valley, and you can see the full breadth of our Fence Installation service if you’re still deciding on materials.
Serving Alamo, CA – Our Local Coverage Area
We serve Alamo and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Aluminum Fence in Alamo
A typical residential aluminum fence of 120 to 160 linear feet takes two to three days on site, with longer perimeter runs on larger parcels stretching to a second visit. Most of the timeline is post setting and concrete cure, which we don’t rush. Call (888) 419-3650 for a firm timeline based on your property.
It depends on your parcel and location, and because Alamo is unincorporated, the answer comes from Contra Costa County rather than a city office. We check the requirement for your specific lot before scheduling and handle the permit where one is needed. Call us and we’ll tell you where your property likely stands.
Most aluminum fence projects here run $3,500 to $9,000, with larger perimeter work at $4,000 to $10,000. Footage, grade of fence, terrain, and gate count are what move the number. Call (888) 419-3650 for a free on-site estimate with a fixed line-item quote.
No. Our estimate is fixed and line-item, and we don’t issue change orders without your sign-off first. If mid-job discovery turns up buried utilities or line issues, we stop and talk to you before anything changes. Call (888) 419-3650 to get that number in writing.
Every fence we install is covered by our 730-Day Done Right Promise, which is one of the longest workmanship guarantees in the residential construction space, plus the manufacturer’s finish warranty on the aluminum itself. Call (888) 419-3650 to schedule your free estimate.
Get a Written Aluminum Fence Estimate in Alamo
We’ll walk your line, confirm footage and grade, and hand you a fixed, line-item estimate for your aluminum fence in Alamo – no ballpark over the phone, no surprise line items later. Estimates are free and everything is covered by the 730-Day Done Right Promise. Call (888) 419-3650 and a live person will pick up around the clock.
Written by the team at Groundwork Construction Co.