Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Walnut Creek, CA: What It Costs and How It Gets Built
A chain link fence in Walnut Creek typically runs $3,500 to $9,000 for a standard residential run, and most jobs are done in two to four days. The number depends on linear footage, height, gauge, gate count, and how much site prep the ground needs first. Call (888) 419-3650 and we’ll walk the property line with you and put a written price in your hands before any crew shows up.

How we build a chain link fence here, start to finish
A fence is only as good as the set. We sequence every job the same way because skipping steps is how posts lean after the first wet winter.
- Day 1 – walk and mark. We confirm the line with you, locate utilities before anything gets dug, and mark post spacing. You decide here: exact corners, gate placement, and whether the fence follows the grade or steps down in panels. That spacing decision is the one most homeowners regret getting wrong later.
- Day 1 to 2 – demolition and clearing. Old fence comes out, roots and hard dirt get worked through. For a typical 150-foot run, tear-out takes half a day to a full day depending on what’s in the ground. You’ll want to decide what happens to the old posts and panels before this stage, since hauling is part of the quote.
- Day 2 – setting posts. Holes get dug, posts plumbed, and concrete poured. In Walnut Creek’s summer heat we pour early and let the concrete cure overnight. Line posts get set first, then terminal posts at corners and gates, because those carry the tension.
- Day 3 – rails, mesh, and gates. Top rail goes up, tension wire strung, mesh stretched and tied off. Gates hang last so they close square against a fully settled frame. You confirm gate swing direction and latch height before we finish.
- Final walk – cleanup and punch list. We haul debris, confirm nothing was left in the soil, and walk the fence with you. Anything standing off gets corrected on the spot.
Small jobs, like a side-yard enclosure or a single dog run, often finish in a single day. Large runs with multiple gates on tight property lines can stretch to a week depending on access.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll actually choose between
Chain link isn’t one product. The specifics you pick here change the price by double and decide whether the fence holds up for ten years or thirty.
- Gauge of wire. 11.5-gauge is standard residential; 9-gauge is heavier and costs meaningfully more but takes a beating from dogs and kids. For long runs along a busy line, we recommend the heavier mesh.
- Coating. Galvanized steel is the cheapest and rusts faster in wet conditions; vinyl-coated (typically green or black) costs more but lasts longer, looks softer against landscaping, and helps where an HOA is watching. Black vinyl-coated chain link now reads as “architectural” rather than “utility,” which is why it’s going up on more of Walnut Creek’s newer custom homes.
- Height and top rail. Four feet is standard, six feet is common for pet containment and privacy. A heavier top rail reduces sag over long spans.
- Gate systems. Walk gates, drive gates, and self-closing hardware for pools all price differently. Automated drive gates add real cost but solve access issues on sloped properties.
- Post footings. Concrete-set posts cost more than drive-in posts, but they hold plumb. On Walnut Creek’s clay-heavy soils and sloped yards, concrete-set is the only way we’ll install on a hillside grade.
What a chain link fence costs in Walnut Creek, CA
For a typical residential chain link fence in Walnut Creek, expect $3,500 to $9,000 installed and permitted where required. That’s the working range, and here’s what pushes a job toward one end or the other:
- Linear footage. A 100-foot side-yard run sits near the bottom; a 300-foot perimeter with compound corners sits near the top.
- Site access and grade. Sloped properties needing stepped panels, or yards with mature trees and roots, add labor. Flat, clear runs come in lower.
- Gauge and coating. Upgrading to 9-gauge vinyl-coated mesh on a large run can add a meaningful percentage to the total.
- Gate count and type. Each walk gate and each drive gate is priced separately. Automated gates land well above the base range.
- Permit and inspection scope. Fences over certain heights, corner-lot sightlines, and any fence on a property line with a recorded easement can trigger plan review, which adds time and cost.
Your written estimate will spell out footage, gauge, coating, gate count, footing type, hauling, and permit work. It won’t include things outside the fence line (landscaping repair, sprinkler relocation, or replacing a gate someone else installed), so if you want those in the job, say so up front and we’ll quote them.
See the difference
Before
After
Before
After
Before
AfterWhat Walnut Creek homes specifically do to this job
Walnut Creek’s market is split down the middle between postwar ranch homes and the newer luxury infill the Lamorinda and Diablo Valley buyers keep pushing in, and a fence contractor has to be fluent in both. On the 1950s-70s single-story ranches and split-levels that still make up much of the housing stock, we hit clay-heavy soils and yards that were never designed with a clean property line in mind, so posts need proper footings and honest grade work. On the newer custom builds, the fence often has to satisfy design review and hillside preservation rules, and that’s where the choice of coating and gate hardware really matters – a utility-grade run won’t pass on a property that took two years to permit. The dry summers also shape scheduling: we pour footings early and let them cure before the heat sets in, because concrete that cures too fast in July doesn’t hold a post. Winter rains push exterior work, so a fence quoted in late fall may not get installed until the ground dries out. Across 94596, 94598, 94597, and 94595, homes often sit on lots where a fence shares a line with a neighbor, so we confirm the line and any easements before we dig.

Serving Walnut Creek, CA – Our Local Coverage Area
We serve Walnut Creek and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Chain Link Fence in Walnut Creek
Most chain link fence installations in Walnut Creek take two to four days from demo to final walk, with simple side-yard runs finishing in one day. Sloped properties, multiple gates, and permit review can push that to a week or more, so we give you a calendar-matched schedule in the estimate.
It depends on height, location, and whether your lot sits on a corner or a recorded easement. Fences within standard residential height limits on interior lot lines usually don’t require a permit, but anything taller or on a sightline triggers review, and we handle the permit work for you so there’s no back-and-forth with the city.
Installed cost runs $3,500 to $9,000 for a standard residential fence, and most projects land somewhere in the middle. Footage, gauge, coating, and gate count are what move it up or down. Call (888) 419-3650 for an exact quote – estimates are free and on-site.
Often yes, but it depends on where the line runs relative to irrigation and planting beds. We flag sprinkler lines during the utility locate and work around them where we can, and if a line has to move, we price that separately so you know what it costs before we start digging.
Every install is backed by our 730-Day Done Right Promise, one of the longest workmanship guarantees in the residential construction space. If a post leans, a panel sags, or a gate stops latching inside those two years, we come back and make it right at no cost to you.
Get a chain link fence quote in Walnut Creek
Walk the line with us and we’ll give you a written price before any work starts – footage, gauge, coating, gates, footings, and permits all spelled out. Estimates are free and we answer calls with a live person, so you’re not leaving a message and hoping. Call (888) 419-3650 and we’ll schedule a time to look at your Walnut Creek property.
Written by the team at Groundwork Construction Co.